JEC

c4Forums Member
  • Content count

    45
  • Joined

  • Last visited

About JEC

  • Rank
    Control4 End User
  • Birthday

Profile Information

  • Gender
    Not Telling
  1. Thanks figured... but wanted to check if I wasn't missing some variable that I could use to tell from what room someone selected the UI button....
  2. I haven't gotten snapshot working on any of my cameras - but have had success with motion and line cross. Bound the generic motion sensor to the camera (once verified working on camera) and enabled push notification. Be sure you enable the "notify surveillance center" on event option. Also link the A#>D# on event.
  3. I setup an experience button that starts the beep on my 260 remote and then stops the beep when selected again. At present, I only have one instance of the UI button.... I would like to use this single instance to trigger the beep for a remote based on the room where the button was pressed... For example, IF UI button pressed (activated) in living room, start living room remote beep ELSE IF UI button pressed (activated) in bedroom, start bedroom remote beep Is this possible? Or am I over complicating things and should have a separate UI button instance in each room that directly corresponds to a single remote? Thanks!
  4. I have ds7716. Would your driver work? What is the process for obtaining? Thanks! Sent from my iPhone using Tapatalk
  5. I have a James Loudspeaker power pipe 1200 matches with their dedicated amp. It is through the floor, mounted between joists. Looks like a HVAC register and sounds great. Expensive but invisible. Sent from my iPhone using Tapatalk
  6. That is correct. You can enable the ports on the NVR so the driver uses 65001..65016 instead of 80 in the confit. ip is set to that of the NVR. This works perfectly in my configuration. Sent from my iPhone using Tapatalk
  7. Nope. It stopped for a bit and started doing it again. You having the same problem? Sent from my iPhone using Tapatalk
  8. Is it possible to query a user for feedback (yes/no/ok) on the touch screen and pause the execution of a program while waiting for the feedback? I have created a custom button that secures the house and sets the alarm mode to stay. I have a message popup on the T3s reminding the user to lock specific exterior doors. It would be great if the program would pause until acknowledgement so the alarm isn't set in stay until the user presses OK. Thanks!
  9. My houselogix wasn't working until I updated to 1.05. Required a director restart to start working again after the upgrade.
  10. I upgraded all my sonos and associated drivers. Now when an announcement triggers through the hc800 the sonos stops playing and does not resume. Is anyone else having this issue? It seems to only effect the sonos device in the room that the announcement plays. I tried taking and recalling a snapshot but that does not bring the sonos music back.
  11. Thanks - will give that a try
  12. Ahh gotcha! Is there a method for matching wav volume to sonos output other than experimenting? I keep my announcements at 35 in the announcement zones and typically listen to sonos ~15-20. I utilized audacity to make announcements so can easily increase their volume.
  13. Thanks CY. Sorry wasn't clear, I have all my announcements normalized. The volume spike is from the Sonos (listening to music) when the announcement ends. Music is loud for a second than returns to its normal volume post announcement. I like the mute/unmute. I could macro that out and call it pre/post announcement to control bleed and I could delay unmute to manage the post announcement volume spike possibly, but that is less that optimal (need to test).
  14. Has a solution been found that works? I am in the same boat, I have many announcements (doors open, etc.). Announcements play from my HC800 but I listen to music via a SONOS. I have a control4 Matrix Amp. I get sound bleed to other zones and volume spikes when listening to music and the announcement fires. I was hoping something could be programmed in Macros a called pre/post announcement to clean up the audio.
  15. I started the Google trial and reauthorized my account in sonos app and everything now shows. Pay to play for radio....