Rob21 Posted January 13, 2022 Share Posted January 13, 2022 My C4 system currently uses Lutron QS for lighting, fans, and shades. The lighting is pretty much rock solid but unfortunately the fan and shade integration is terrible. The fans and shades are controlled with QS wireless. I believe that the homeworks QS shade integration is known to be problematic but I am wondering if anyone has any input on integration with homeworks QSX. If homeworks QSX offers solid integration for shades and fans then I would definitely consider upgrading. Any input is appreciated! Quote Link to comment Share on other sites More sharing options...
tekki70 Posted January 14, 2022 Share Posted January 14, 2022 what are the issues you are having with qs, i have done plenty of QS and QSX and have not had any issues, it could be your original programmer is not well versed integrating the systems together Quote Link to comment Share on other sites More sharing options...
Rob21 Posted January 14, 2022 Author Share Posted January 14, 2022 5 hours ago, tekki70 said: what are the issues you are having with qs, i have done plenty of QS and QSX and have not had any issues, it could be your original programmer is not well versed integrating the systems together To tell you the truth I would not be surprised if that were the case. I have two main issues. (1) My shades do not operate properly with the original Lutron qs shades driver. The shades operate fine if I control them through Lutron but when I attempt to control them in C4 it can be very finicky. Sometimes it takes multiple inputs for the shades to start moving, if the shade is closed and I drag the slider to 100% open it often stops at 99% instead of 100%, etc. (2) My fans do not track properly in C4. For example if I drag the fan slider to a medium speed it will set the fan to that speed but when I leave the page with the fan speed on whatever device I’m using and go back to it the fan slider reads that it is off. In order to actually turn the fan off I need to move the slider to one of the on positions and then move it back to off without leaving that page. I hope that all makes sense. I appreciate all input/help. Quote Link to comment Share on other sites More sharing options...
chopedogg88 Posted January 15, 2022 Share Posted January 15, 2022 these issues can most likely be fixed by updating your drivers and/or swapping out the shade drivers to a different one. PM me if you need remote assistance. Quote Link to comment Share on other sites More sharing options...
tekki70 Posted January 15, 2022 Share Posted January 15, 2022 22 hours ago, Rob21 said: To tell you the truth I would not be surprised if that were the case. I have two main issues. (1) My shades do not operate properly with the original Lutron qs shades driver. The shades operate fine if I control them through Lutron but when I attempt to control them in C4 it can be very finicky. Sometimes it takes multiple inputs for the shades to start moving, if the shade is closed and I drag the slider to 100% open it often stops at 99% instead of 100%, etc. (2) My fans do not track properly in C4. For example if I drag the fan slider to a medium speed it will set the fan to that speed but when I leave the page with the fan speed on whatever device I’m using and go back to it the fan slider reads that it is off. In order to actually turn the fan off I need to move the slider to one of the on positions and then move it back to off without leaving that page. I hope that all makes sense. I appreciate all input/help. it definitely sounds like your programmer made some mistakes that can be fixed, your system should absolutly not be running like that. reach out to Chopedogg88 and let him run through your system. the problem may be a little deeper than c4 integration it could be issues on how its setup within lutron but it can be fixed., again reach out to chopedogg88 as he can help you as well Quote Link to comment Share on other sites More sharing options...
fabiopogi Posted July 20, 2022 Share Posted July 20, 2022 Hi Guys, hope you can give me some help. We are facing some issues here integrating Lutron QSX with Control4. Every time we change a Pico button programming, all the light zones inside this programming stops responding on Control4. I can only make them responsive again if I delete all of them on Control4, go to the processor driver and ask to add zones again, this helps making the lights responsive again, but I can't do any programming on C4 once the light zones change every time. Have anyone a clue on how to solve it? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.