dlaugh Posted September 4, 2022 Share Posted September 4, 2022 I have a NYCE motion sensor in our master closet. It is set to turn on the closet lights and "start" a count-down timer. The Stop Motion Delay value for the motion sensor is set at 20 seconds. The "if running" explanation for the timers agent says "(if running): Starts the timer over and fires the 'reset' event. Timer state: Running." The way I interpret the above, then, is that after first detecting motion the NYCE sensor waits 20 seconds and, if it detects motion after that period, it fires off another "motion detected" signal and the timer should reset. The count-down time is set for 1 minute, so there should be an avenue of 40 seconds for motion to be detected and the cycle to start again. That never happens. I could be doing jumping jacks in the closet and the counter never resets. I've enabled logging in the NYCE sensor and it appears to send a "no motion" signal after roughly its Stop Motion Delay and then does nothing after that. (Log for two events below, what I believe to be a motion signal and that a no-motion signal.) It faithfully detects initial entry into the closet but then appears to ignore motion after that. Any ideas? Thanks! OnZigbeePacketIn: offlineTimer=7707501 gInterval=240 SZL: --------------------------------------------------- SZL: SZL.ProcessZigbee -- Profile: 0x104 Cluster: 0x500 Data: 00000000 19 1F 00 32 00 00 01 00 00 ...2..... SZL: APS Frame Control: 19 Frame type: Cluster Specific SZL: ParseZHeader -- Cmd: 0 (Cluster Specific Cmd) Seq: 31 SZL: Data: 00000000 32 00 00 01 00 00 2..... SZL: Cluster Specific Command .. Sending to Handler... Handlecommands: 0 00000000 32 00 00 01 00 00 2..... IAS Zone cluster command Zone Status Change Notification OnZigbeePacketIn: offlineTimer=7707837 gInterval=240 SZL: --------------------------------------------------- SZL: SZL.ProcessZigbee -- Profile: 0x104 Cluster: 0x500 Data: 00000000 19 20 00 30 00 00 01 00 00 . .0..... SZL: APS Frame Control: 19 Frame type: Cluster Specific SZL: ParseZHeader -- Cmd: 0 (Cluster Specific Cmd) Seq: 32 SZL: Data: 00000000 30 00 00 01 00 00 0..... SZL: Cluster Specific Command .. Sending to Handler... Handlecommands: 0 00000000 30 00 00 01 00 00 0..... IAS Zone cluster command Zone Status Change Notification Quote Link to comment Share on other sites More sharing options...
msgreenf Posted September 4, 2022 Share Posted September 4, 2022 Add the courtesy light driver. Select the sensor. Delete all programming and configure the driver. Quote Link to comment Share on other sites More sharing options...
fleon Posted September 4, 2022 Share Posted September 4, 2022 5 hours ago, msgreenf said: Add the courtesy light driver. Select the sensor. Delete all programming and configure the driver. Courtesy light driver? I don't see that one. Can you give some more details? Do you mean the security-courtesy light? Quote Link to comment Share on other sites More sharing options...
msgreenf Posted September 4, 2022 Share Posted September 4, 2022 15 minutes ago, fleon said: Courtesy light driver? I don't see that one. Can you give some more details? Do you mean the security-courtesy light? Yes that is the driver Quote Link to comment Share on other sites More sharing options...
dlaugh Posted September 5, 2022 Author Share Posted September 5, 2022 Confirming that worked! This shows up in the driver list as "Security Light" and then when added populates as "Security-Courtesy Light," as suggested. Thank you. msgreenf 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.