Jump to content

avittech

Control4 Dealer
  • Content Count

    263
  • Joined

  • Last visited

Everything posted by avittech

  1. we normally vent the closet to conditioned space with various fan kits made for this. Need to determine the BTU you are trying to vent and where you will vent it to
  2. The serial should be straight through. Here is the manual - https://www.dropbox.com/s/qrd5kxlx8ecn1at/Leaf_ZLE-LTHDMI88E.pdf?dl=0 3.8 RS232 Serial Control connectors The unit can be controlled by serial commands through the RS232 input port. Typically this would be connected to a control system with a straight through DB9 Male to Female RS232 lead. Some control systems may require only the TxD, RxD and Gnd wires of an RS232 lead to be connected. The pin configurations of these 3 connections on the DB9 plug is: TxD = Pin 2, RxD = Pin3, Gnd = Pin5. 3.8.1 Single LTHDMI88/E use The RS232 Input port is used for controlling the unit. The TERM (Termination) switch (ref: para 3.10) must be set to ON (Up).
  3. There is no warranty left on the unit and yes it does work fine. Was traded in to upgrade to 10x10 4K matrix.
  4. C4 owns leaf and originally sold the leaf branded units before branding them as C4. Yes, it is 1080p
  5. sorry about that. was just showing original cost and part#'s included yes, $1000 + shipping for all
  6. The landscape system I can do for $3500
  7. I have a new in open box (literally, unpacked and powered on, never used) Sonance DSP 8-130 Amplifier I will sell for $1200 shipped There are no scratches, blemishes, or anything wrong physically or electronically. This amplifier is 100%. Rack ears, power cable, original box and packing material. Original manual. 4 input 4 output audio matrix. Full DSP control Built in Digital DSP Crossovers (Can be a full surround sound system with sub) A 10-band parametric EQ. Web page based configuration. Volume and Gain controls. Option Digital input modeul 130 Watts RMS per channel (all channels driven) @ 8 ohm 145 Watts RMS per channel (all channels driven) @ 4 Ohm 1U Rack Space 24 bit/96K DAC Also, have a Landscape System - LS47 System with DSP 750 and LS10 Sub - contact me if you are interested.
  8. I have a couple of the cards. Will sell for $50 shipped each or $80 for both. Both cards have been sold
  9. I have this Binary 8x8 with HDBase-T and HDMI outputs. Power over Cable. 6 HDMI Receivers. New in box. Selling below cost - $3200 shipped https://www.snapav.com/shop/en/snapav/switchers/binary-trade%3B-hdbaset-8x8-matrix-switcher-with-(6)-hdbaset-receivers-(230)-with-poc-kit-kit-520-8x8mx-6rx
  10. I have this exact setup working perfectly for 3 years now. Through all of the firmware's. I would look at the network.
  11. I have a like new Binary HDMI 8x8 Matrix Switcher with HDMI outputs. B-100-HDMATRIX-8x8 Unit was replaced with a 10x10 HDMI 4K Matrix Comes complete in box as new. $1000 shipped
  12. There was also a sonos driver update recently - we have had to reboot a couple of controllers for sonos to work again.
  13. The nyce are very small and work great. They do not have light or temp sensors. If you need it this small, you have no other option. The Axxess also work great and have temp, light, and optional humidity sernsors. I use both in my home and they both serve their purposes great.
  14. http://www.atonhome.com/DLA2Room.html
  15. The problem with most digital audio matrices is they do not usually down convert dolby digital and will only accept a PCM source, which is 2 channel. If you want to watch movies in surround on your appletv and have the digital output work for secondary zones you will have to set the appletv to pcm.
  16. Go with Alan's driver. It works very well. We have done it a few times.
  17. I have used it with the S15 and S20 many times.
  18. Yes you should be ablt to use it. The Aux Keypad uses Neutral and a traveler back to the original dimmer to work. It does not need Hot. You can use a Configurable Keypad as long as you have hot and neutral at the location which you should be able to wire if you have the traveler wire you wee going to use for the Aux keypad. Hope that makes sense.
  19. The Tivo mini has an issue with IP control. where it will become unresponsive to commands when you get the "Delete this recording?" dialog at the end of a recording. The only way to get out of this is using the iPad/iPhone TiVo app or the ir remote. It affects only the Mini at this point and it seems it is an issue with Tivo's software
×
×
  • Create New...