RAV

Primarily Bug Fixes and Connect Requirement. https://www.control4.com/docs/product/control4-software/dealer-release-notes/english/latest//control4-software-release-notes-rev-as.pdf

You could bypass the fan output of the Control4 Fan Speed Controller essentially turning it into a KC120 and run the hot direct to the new fan. Then reprogram the buttons as you'd like. But I don't think you'll be able to 'add' an up/down to the fan controller driver in composer. But no the KCB is not a choice as it's 48v power and RS485 for panelized lighting. KC120 would be the choice.

Much of it comes down to the cost of entry, exclusives and job security. If you have the related Certification, than you're going to spec their hardware, in part to lock out those that don't have Certification. It's a Union thing.

How often do you loose power? For how long? You may want to invest in a UPS for your processor and matrix (and other related non amplifier components)

Trying to make a pizza from a picture you saw. It’s just bread, cheese and tomatoe sauce.

Correct on what I was thinking. Whether it's one driver with subheadings or using multiple instances of the driver, would depend on what's possible within the driver architecture itself. It was thinking multiple instances to keep from long scrolls to find the info you want.

and there's also Presence Sensors rather than just motion: https://chowmain.software/drivers/control4-athom-human-presence-sensor

I understand your point. I'm just saying, make the timer longer and you'll likely have a better experience without adding more programming and complications.

Make the timer much longer. You've added a pain point that's not resulting in significant savings. If you're using LED the cost savings between a 5 minute occupancy off and a 30 minute is going to be less than a latte a year. Average kitchen LED lighting, it's about $6 a month if left on 24 hours a day! Which is about a penny per hour.

But I can create a user variable to match a driver variable. So was wondering if the driver allows multiple lists in one system for displaying that information to end user in one place, not so much manipulating the variable. Show all lock status, HVAC values, alarm window contacts etc.

Then there should be a Garage Door driver in your project which you'll program against, it's not a variable. You need a timer - for however long you want the delay to be. GarageTimer Then in programming tab When Garage Door opens, reset timer GarageTimer When Garage Door closes, stop timer GarageTimer When GarageTimer expires - close door

Do you have a garage door icon that's currently reflecting the state?

I display list per project? For example. Cool Setpoint list - shows all the tstat cool points in the house Heat Setpoint list - shows all the tstat heat points Current Temperature list - etc

Fixed

Nice !

https://status.snapone.com/

Probably not you. Post in the dealer forum about slow loading this morning, reproduced by and service ticket thus created by a Control4 employee.

Remote buttons get their function from the source device driver, ie cable box. To change what a button does to a source you have to edit that driver, most drivers are not easy to edit. You can program at the room level additional commands to any remote button, which are based on the sr series remotes nomenclature. If no source device uses the page up down, you’re good. If any do, you get both the device and the room level commands. Adding if source is xyz type commands at the room level for a button you can send those additional commands for only devices that don’t have device commands. (You can not prohibit a device level command through programming, only through editing the device driver)

Put a Shelly relay inside the box and use the outlet vendor of your choice.

If you have standard wall plates with screws, you should be able to discharge yourself by touching the plate screw first. Maybe snapoff the screwless plate for a bit to confirm issue as it'll expose the screws. Humidifier can help.

I’ve done it as a no control source. Addressing your 24/7 commercial need more so than a user changing stations on the fly. They have their own user interface to setup scheduling channels etc.

https://pandora.moodmedia.com/

Our Engineering Team has been working directly with Roku to resolve this issue. With this engagement, Roku has identified the cause and has been rolling out a solution since last evening. It should be complete by the end of the day today, April 5th. The fix to restore service will be automatic—neither you nor your customers will need to take action. We are monitoring the rollout of the fix to confirm that the issue has been fully resolved. Apr 05, 2024 - 14:28 EDT

You can have the projector and receiver drivers be unhidden so they show in the Watch menu. Selecting them will then allow you to issue their menu commands and navigate them, then remember to close their menus, and re-select your active source. Dealers customarily hide them as most users would only end up screwing up settings.

Control4 quoted Roku in the dealer forum.