Jump to content
C4 Forums | Control4

Jas0r

c4Forums Member
  • Posts

    61
  • Joined

  • Last visited

Everything posted by Jas0r

  1. Has the lite driver been updated in line with the full driver? Mine is on auto update but has not found it.
  2. I started with using the dls software doing everything over ip. In the end I reset the tl280 to factory defaults using the jumper method as per the manual then did all my config for C4 from the keypad. You can still use dls for programming the alarm just stay away from the communicator settings.
  3. Ok I finally got it going, been playing with it for most of Saturday getting nowhere. I initially programmed it with the control panel but using the PDF instructions that had the wrong 426 setting and then after that due to ease I have been using DLS for the programming of the alarm and not from the control panel. I had reset the TL280 from within DLS a few times with no luck. Decided to wipe the TL280 using the jumper as per the manual and start again using only the control panel and guess what, first pop it went. Frustrating but happy it goes. Thanks @andypaul for your help much appreciated. I have both C4 and the Neo Go app working. Now to set up trigger notifications. PS does anyone know how to grab the camera feeds from the PIR if they are built in. I have a few of these and that would be fantastic if they got linked in also Wireless PowerG PIR Motion Detector with Integrated Camera
  4. Yes I have followed the driver docs, the main change is in 426 which I have tired as 3 only and 2 & 3
  5. Ive been following the one you attached earlier. It has option 2 enabled. I have tried it now without and same result
  6. Sure have 425 = 3 & 5 426 = 2 & 3 428 = 192.168.10.5 which is C4 HC-800 running director 429 = 0C00 711 = 00000078
  7. Hi Thanks, I have been using 8 digits as per the guide. Tried all 12 but still the same result :/ This is my properties page In the installer info I have put : User Code = 4 digit Master code that is used to arm and disarm Installer Code = 4 digit code to enter installer functions under *8 Peer Key = all 12 digits from [851][422] Own Key = 8 digits from [851][423] which is just the default 12345678 There just doesn't seem to be much else I could get wrong unless some other integration setting that shouldn't need changing is wrong although I have checked all the settings to ensure they are as per the defaults.
  8. Andy Thanks for your response, I tried rebooting the panel ages ago but with no luck this time it at least started to talk as per the debug log below but something must still be wrong in the config. Just to confirm, the installer code is the code to enter the installer section of the alarm (via * 8) not the IP installers code which is a different code. Also the peer code is the first 8 of the 12 numbers read left to right not right to left ie 123456789012 = 12345678 not 56789012 Server Connection Established: 207699862 Protocol Version is: 2 17 Command Queue is empty. Command Queue is empty. Command Queue is empty. Command Queue is empty. Command Queue is empty. Couldn't dispatch message from panel... Command Queue is empty. Command Queue is empty. Not ready to poll yet Not ready to poll yet Not ready to poll yet Server Connection Disconnected: 207699862 ...restart... Not ready to poll yet Not ready to poll yet
  9. Hi Just wondering if anyone has comments on this? I have managed to get C4 to see the communicator only when the DLS software is connected to the communicator. There must be some polling or something happening when this communication happens but it never initialises correctly and looses connection when I disconnect DLS. Im sure its just a setting somewhere in the config. I have reset it all to default several times with no luck and I have also updated to the latest firmware of 5.21 for the TL280 and 1.31 for the panel. Thanks
  10. Hi, I have just got my system set up. I have the TL280RE V5.03 and a NEO HS2128PCB board I can get the Neo Go app to work but I cannot get C4 to connect. I have followed the settings in the pdf to the letter but all I get is "establishing communication". Are there any other tricks as it just doesnt seem to be polling. If I turn on debugging it says "Not ready to poll yet"
  11. Firstly awesome driver, so many options. I am using this with a google home. Is it possible to answer a question with a question using google home? I would like this just to make it a little easier to know the answers so you can prompt an answer rather than remembering to string together a long request. ie "Turn on radio" google home response - "What station would you like station a, station b or station c" "Station A"
  12. Firstly great driver it works flawlessly for me and is used daily as our primary interface. I have been trying the latest alpha due to the netflix support. I know its alpha and will probably change greatly but I thought I would point out the driver seems to detect kodi but the controls dont work stating "bad client permission" in the debugging. Just in case there is a future change to make for when its finally released
  13. Its a Raspberry Pi, I changed the port to 8080 (from 80) and rebooted and its kicked into life. Thanks Time for a play but it looks like its well worth a purchase.
  14. I have installed this driver following the install instructions but its remaining as disconnected. I have the IP correct and the port, I have set the remote access setting also. Is there any other debugging I can try?
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.