lostndashuffle

Customer is switching from Xfinity, they have directv at their other locations, they want it here but do not want the sat outside. ATT fiber to home, ordered directv stream and the gemini air devices. Anyone have experience in integrating the gemini air devices into c4? (neo, sr260 remotes, ea5) Main things are channel search via number pad, and quick channel launch via favorites?

Install them locally and can ship them? Is it a special device or are you sending like an apple tv or roku?

Both came with os3 on them, existing ea3 had all zigbee working on it, then it stopped

For testing, I have disabled any 2.4ghz wifi, and stood within 5 foot of the controller with both zigbee devices. It will not add to existing ea3, boot up brand new ea3, both will add to system.

Ea3 is on the shelf of the entertainment system, one room over. Took the sr260 remote straight to the controller and it would not add into system. Only one access point, I have 2.4 channels separated. 10 acres separates from closest neighbor, not seeing printer wifi broadcasting either. I manually set the 2.4ghz to channel 1 and zigbee is on ch11. The z210 was only for ir control not used to extend network.

It is. It's looking like it is the ea3, I had another ea3 I loaded everything onto and the zigbee worked fine.

Hey, Site has EA3 with 1 CRZ2IO, a sr260, neo and Halo. the Neo, Halo work just fine (everything they control is IP. the SR260 controls 2 IR devices, and 1 IP device (IP device works flawless). Looked at zigbee health, the CRZ210 showed great signal but was in critical condition (520 failures an hour), the sr260 would just not respond, tried power cycle, re-address to controller, then factory resetting. no change. Facrtory reset the controller, any zigbee device will not add into the system, get to enrollment screen and no matter what I do no device will enroll, grabbed a brand new sr260 and z2io, same thing. Any ideas?

They are wired, wifi is not connected. Static at tv and reserved in router, no conflict with another ip address. In the network tab they are set via ip not sddp, before removing ssdp mac I verified ip address was correct. They are paired properly

In these situations art mode is not being utilized for the issues to arise.

Samsung are up to date

It is. (Stated near end of description)

Every Samsung on this site reacts very similar. Sometimes they will bootup on scene start immediately, sometimes they have 10+ power retries. Sometimes when powering off they go right off, other times, they will act like they power off with the screen showing so, then tv will turn back on, have to start a scene and power off a scene to turn off after that. All this will happen even if giving a tv 45+ seconds after powering off. Or even 5 minutes. Attached is one of the rooms tv settings, and its Lua output. Also, why is it sending input commands when it has no confirmation of powering on? How can I get the tv to respond better on ip commands? Tv is static ip, in network it is also static without Mac address. Have tried with both, have tried with one of each. Tvs are all 2022 samsung frames, ranging from 43"-85"

what driver are you using for rs232 control on the samsung frame??

So, in taking all of these screenshots and what not, the stupid thing has started working, I deleted the if programming to verify. Weird... still connected to home theater input...

Hello, maybe someone can point me to the issue solving correction! Setup is Nvidia Shield - Samsung Frame - Sonos Ray Soundbar Connections - Shieled HDMI Output - Samsung TV = (Video Endpoint to tv) Samsung TV Optical Output to - Sonos Ray Optical input Control - Halo and Neo Remote Before adding the Sonos Ray everything functioned and was controlled through the remotes added the Sonos Ray through Sddp, IP address is correct, it shows online in network tab. I get no control with the remotes in regards to volume up/down, mute. When pushing said buttons, Optical output image displays on tv, but no change of state via Sonos. (I can control volume through Sonos app). I'm assuming I am missing a connection or something - Documentation was stating I should only need the optical connection, no other audio/video audio endpoints needed, unless I am misunderstanding. I was able to go into programming and assign when volume is pressed pulse volume up, same thing for volume down, and set a volume toggle, which those programming commands work on the Sonos Ray. I get no feedback on the remotes screen as to the volume level, and the optical image still appears on the tv. <- this was just a workaround for the time being, I assume theres a better way to integrate this into the system, and get smart feedback at least on the remote for volume control and get rid of optical flash on screen? Ea3, Nvidia Shield TV, Samsung Frame, Sonos Ray Halo non touch, Neo Remote

oops, I remember reading that now, I added the driver, just not seeing anything in connections, I see where I can assign it to the ea controller but, not much else. I assume I am in the wrong location in Composer Pro, any pointers?

have you used this driver?

Been having trouble with Samsung Frame with IP commands, i have it assigned via IP, there is sometimes long delay in power up sometimes withing a few seconds, but when setting a watch scene, frame will boot up, and then only sometimes switch to the proper input. otherwise it uses last input before powering down. if i select the input its on i can run that scene, then i can start a different watch scene and it will change to proper input.

using sr260, I have the factory remote which I used to repair the tv

in connections - network - when powered off they show not addressed. can power the tv back on for a watch scene, will then show the correct IP and Mac address. Will not launch the correct input on start of watch scene, will use last used input, after switching to that device via the remote, it will control that device, then i can start a different watch scene and it will swap inputs as intended

Does that seem to be pretty solid doing it that way?

What did you end up doing?

"for those that can"? have you used it yet?