Jump to content
ILoveC4

Lutron Caseta Integration

Recommended Posts

I just purchased a caseta fan control, and pico remotes for audio, shades, dimmer, and fan. Going to integrate it with a tp-link kasa dimmer, sonos / marantz 1508, and somfy shades. I'll use c4 to drive macros from the pico remotes. Seems like a great way to integrate all the systems I have now.

For the last 8 yeas I used c4 plus sonos...

Now I am c4, sonos, Philip's hue, lutron caseta, somfy, and Alexa. Let's see how it all works together.

Sent from my SM-N950U using Tapatalk

Share this post


Link to post
Share on other sites

54 minutes ago, thegizzard said:

I just purchased a caseta fan control, and pico remotes for audio, shades, dimmer, and fan. Going to integrate it with a tp-link kasa dimmer, sonos / marantz 1508, and somfy shades. I'll use c4 to drive macros from the pico remotes. Seems like a great way to integrate all the systems I have now.

For the last 8 yeas I used c4 plus sonos...

Now I am c4, sonos, Philip's hue, lutron caseta, somfy, and Alexa. Let's see how it all works together.

Sent from my SM-N950U using Tapatalk
 

Can you send me a picture of the fan control installed in a box next to a C4 Keypad/Keypad Dimmer?

Share this post


Link to post
Share on other sites
Can you send me a picture of the fan control installed in a box next to a C4 Keypad/Keypad Dimmer?
I can when I get home later.

Sent from my SM-N950U using Tapatalk

Share this post


Link to post
Share on other sites
31 minutes ago, thegizzard said:

I can when I get home later.

Sent from my SM-N950U using Tapatalk
 

That would be awesome. Thank you!

Share this post


Link to post
Share on other sites
19 minutes ago, thegizzard said:

This is the best I could do I didn't have any c4 stuff not installed. 09d82bb4b05e9dcbd65d74b5d5b1c157.jpg

Sent from my SM-N950U using Tapatalk
 

Thanks! I was hoping for a side by side pic of a C4 keypad or keypad dimmer with the Caseta dimmer - with them both installed. If that’s convenient, awesome. If not, NBD. 

Share this post


Link to post
Share on other sites
53 minutes ago, thegizzard said:

This is the best I could do I didn't have any c4 stuff not installed. 09d82bb4b05e9dcbd65d74b5d5b1c157.jpg

Sent from my SM-N950U using Tapatalk
 

Loosen and line up all the wall plate screws all either east west or north south. Not screw until you can’t anymore. 

 

My ocd cannot handle that 

Share this post


Link to post
Share on other sites
Has anyone integrated the fan control for Caseta yet? Is there a driver for it? Can you use the Ra2 Select fan driver?

I have 3 installed. You will have to use the RA Select driver. Works great.

Share this post


Link to post
Share on other sites
Loosen and line up all the wall plate screws all either east west or north south. Not screw until you can’t anymore. 
 
My ocd cannot handle that 
Lol. Much appreciated. After 2 kids and a dog making a mess of things I don't even see things like this anymore.



Sent from my SM-N950U using Tapatalk

Share this post


Link to post
Share on other sites

Just upgraded to 3.0 and my Lutron shaded are not functioning properly...dealer tried new drivers...cant figure ti out...anyone have the skill set for remote programming on this...happy to pay!

Share this post


Link to post
Share on other sites
7 minutes ago, Control4@8293 said:

Just upgraded to 3.0 and my Lutron shaded are not functioning properly...dealer tried new drivers...cant figure ti out...anyone have the skill set for remote programming on this...happy to pay!

Define "not working properly".
What exactly is not working?

Share this post


Link to post
Share on other sites
2 hours ago, Control4@8293 said:

Just upgraded to 3.0 and my Lutron shaded are not functioning properly...dealer tried new drivers...cant figure ti out...anyone have the skill set for remote programming on this...happy to pay!

If it's a RA interface, be sure you're using a unique user and password for the Control4 driver, not the default/main programming interface user/pass.

 

Share this post


Link to post
Share on other sites

Hello, I'm working on integrating 6 Caseta controlled shades with C4 OS3 but I've run into a strange issue that affects all the shades.  The controls work fine, but when the shades are closed (0% open), they fall off the touchscreen navigators and cannot be controlled.  When I use a pico to raise them to 1% or higher, they come back and are controlled just fine.  

Seems like a driver issue - has anyone else seen this?  Thanks for any suggestions.

Share this post


Link to post
Share on other sites

Hi, I found that the default view in the OS3 navigator is to show active devices only and to see the shades that are 0% open (not active), you need to press the show all button with 3 lines on the bottom of the screen.  Is there any way to change the default view to show all?

Share this post


Link to post
Share on other sites

Homeworks QS. Nothing is better or more versatile. While it is expensive and doesnt fit all budget or applications, in the instance of new construction a properly planned, wired and installed panelized lighting system has so many benefits. Having worked on C4 lighting, RA2, caseta, Homeworks interactive, Homeworks illuminations, QS reigns supreme. 

Share this post


Link to post
Share on other sites
On 6/3/2019 at 11:30 AM, BakerBalay said:

chopedogg88- create a scene in the Caseta app and have an advanced lighting scene call that Lutron ID- your popcorn with disappear completely.

 

ILoveC4- there is no double tap option in Lutron except for Homeworks. If you want to try this off a Pico in Caseta, you can leave that button unassigned to any loads in the Caseta app. Set up a variable and have the Pico button programmed to cycle through the variable. Each number gets a different scene, and then resets to off. Homeworks calls this a sequential. Using this in an ancient RadioRA2 scenario and even have the LED readout in RA2 following via programming, but the rest of the family had a hard time dealing with the change when I made it! 

You could run Caseta for the switching/dimming/fan control, and run C4 keypads for all the programming functionality and the Zigbee mesh. And make sure to get the SmartBridge PRO through distribution, jackstiffer is right- the HD SmartBridge (no PRO) does NOT integrate at all.

I would love to accomplish this as well, however, I don't see lutron caseta ID's assigned to scenes.  All scenes have ID #1 along with the smartbridge pro, however, have subsequent "numbers".  The first two are predetermined, and the ones I've created begin at #3 within ID #1.  I'm not seeing in Composer Pro how I can assign a subgroup under the ID assignment to get to the number.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...