-
Posts
8 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Gallery
Downloads
Events
Posts posted by JeremyK
-
-
Thanks Cyknight. I was just hoping there would be someone on here with some more insight as to when the "is coming" might be referring to. No need for any other comments other than yes, no or I don't know.
-
Has there been an update yet that allows for scheduling or presets to be made from Control4? Saw the original post from 2018 and it said its coming. 2 years later so im hoping the answer is yes.
-
Has anyone used this driver yet?
-
Found that if you turn off force arming in the security panel that if you go to arm with zones open the c4 app or touch screen will prompt you to bypass the zones.
-
Has anyone successfully integrated a NEO panel using the TL-280 module and been able to figure out a way to enable zone bypassing? This is now showing up in the interface right now and I can't seem to find a way to enable it. Please help.
Thanks,
-
On 8/23/2018 at 6:44 PM, TxHillCountryC4 said:
I have had Control4 talking to my TL280 (5.03) and HS2032 for some time now since my C4 2.10.2 system has been fully functional for the last 6 mos or so. I am able to arm and disarm the alarm in C4 within my LAN and outside the home as well. I have read all of the forum entries here and other places and as I take another run at this I just need a level set.
The PDF document referred to in this thread as well as others shows things that I do not see in Control4 on any of my navigators. My various security windows look similar to what I see in the PDF but....SHOULD I BE ABLE TO SEE:
1. Status, Zones and History tabs at top? I do see status and zones off to the left on the iPhone navigator (see attached screen print). I have NEVER seen the history tab exposed. Zones and status work fine and show all the zones in my system albeit with some mislabeled doors vs windows etc (I understood this was fixed with the old Domosapiens IT-100 serial driver).
2. Should I see "Security Panel" or "Partition 1" in the navigator. For the attached screen print this dialog was opened under the heading security panel. Occasionally I see Partition 1 as the entry point but all other points here remain the same.
3. MOST importantly I have never been able to use the functions menu from within C4 for such things as bypassing zones while away from the house, temporary codes and the other things I would hope that would be here should the functions icon ever show as enabled.
All items in the driver seem to look as everyone has explained here but I just wanted to confirm as it is not 100% clear in these forums or in the PDF if the extended functionality I am after should be enabled with the latest driver, C4 version and other linkages here (protocol version is 02.17) and I am using AES-encryption 128 and of course all my keys are working (show true) and IP is communicating. It stops if I reset the TL-280 but always comes back in a few minutes. I just never see history or a functions menu enabled.
Should I?
Thanks in advance.
Did the bypassing feature ever get resolved using the TL-280? I have the same issue.
-
We have a new Neo panel installed with the TL-280re module on it for integration into the Control4 system VIA serial connection. What i'm noticing is that there is not a way to bypass zones from the C4 app or touch screens. Has anyone else seen this and is there a way to fix it?
Lutron C4
in General Control4 Discussion
Posted
I have the same setup but for some reason none of the dimmers are working through C4. I can parse the project from the RA2 driver in C4 and get the device ID list from C4 which means the main repeater driver is working. Not sure why none of the dimmers are though. I used the RA2 dimmer for all my Pro dimmers and for the keypads as well because I dont want them to show up as keypads just want the light load that is attached to show up. Any ideas why the dimmers are not working in C4?