NapTown Posted June 13, 2011 Share Posted June 13, 2011 I'm not able to see and hense not able to add a room of audio. By this I mean sometimes I'll go in my kitchen and want to select my garage to have it start playing but the zone doesn't show up as an option when I click on add rooms. I've created a fix with a media scene and to get it to shows up but it's not idea. Any ideas? Link to comment Share on other sites More sharing options...
Intellisol Posted June 13, 2011 Share Posted June 13, 2011 Have all the audio end points been set? Link to comment Share on other sites More sharing options...
NapTown Posted June 14, 2011 Author Share Posted June 14, 2011 Yes I believe so. To help clarify, the problem I'm having is with the selection of zone volume with my TV's and Ipad. I have 6 zones of audio current running; Living, Dining, Master, Kitchen, Garage, Patio. When using the living room tv display I go into listen-zones and click on add rooms. I currently only have the kitchen showing up. I click on add rooms and it doesn't give me any options other than All Rooms and Kitchen. If I then go in and select media scene on the ipad that has another zone in it, for example my kitchen and living room, then immediatly deactivate the scene it shows both zones and enables me to change the volume on each on the ipad, but not the tv display. TV display still only shows the kitchen. I then go to add zones on the ipad and still no other zones show up but the zones I just activated through the media scene. Any help is greatly appreciated. Thanks Link to comment Share on other sites More sharing options...
itsbmw Posted June 14, 2011 Share Posted June 14, 2011 I am trying to figure this out too..I installed an 8-zone amp last night, all my audio and volume endputs are set to Audio Input 1 and Audio Volume 1 for each room, and I made a driver called Sonos with an RCA output and linked 3 of them to Inputs 1 2 and 3 on the amp. What I am trying to do is use 3 Sonos ZonePlayer 90s.http://sonos.com/products/zoneplayers/zp90/default.aspx?rdr=true&LangType=1033But none of them show up in the zones, or under any rooms. Link to comment Share on other sites More sharing options...
Godzilla Posted June 14, 2011 Share Posted June 14, 2011 try refreshing navigator Link to comment Share on other sites More sharing options...
NapTown Posted June 14, 2011 Author Share Posted June 14, 2011 Yes refreshed with navigators many times. Link to comment Share on other sites More sharing options...
itsbmw Posted June 14, 2011 Share Posted June 14, 2011 Upload your project, Idk how to put into words what I did, but I was having this issue and fixed it. Ill see if yours has the same issues. Link to comment Share on other sites More sharing options...
DrDSL Posted June 15, 2011 Share Posted June 15, 2011 This _really_ sounds like an A/V binding or end point connection issue in Composer programming. If you want to upload your project, we can take a look at it. Link to comment Share on other sites More sharing options...
NapTown Posted July 13, 2011 Author Share Posted July 13, 2011 As someone stated it was an audio endpoint issue. I finally isolated it and figured it out. This also fixed a door bell issue I was having. Still trying to fully comprehend the endpoints. Link to comment Share on other sites More sharing options...
SerJ_G Posted September 16, 2011 Share Posted September 16, 2011 2NapTown, please, write down the solution for this problem. I have one in one the same problem with my 8 zones Amp. Link to comment Share on other sites More sharing options...
NapTown Posted September 21, 2011 Author Share Posted September 21, 2011 As stated in my previous post it was an endpoint issue. I can't recall the exact endpoint that wasn't correct but I figured it out by using the interviewer and reloading my project one device at a time. This took a little time. I compared this to my full project and figured out the endpoint issue. Frankly I'm still not 100% on the endpoints but I did get mine to work. I wish there were a tutorial on it. I get the basics but some of these endpoints can get confusing. Link to comment Share on other sites More sharing options...
SerJ_G Posted September 22, 2011 Share Posted September 22, 2011 May I ask you to upload your project? I'll try to compare you connection with mine.I didn't have Audio switch, just Amp v3 16. As I understand it can switch chanels, and Audio switch is needed when there are more than 8 zones. Link to comment Share on other sites More sharing options...
SerJ_G Posted September 23, 2011 Share Posted September 23, 2011 UPD:I figured it out - after making all connections in project (set amp as audio end-points and volume control in proper rooms), project should be backed up, then cleared from director and then reloaded back. After that all zones will be in navigator and switching them on/off will works O.K. Link to comment Share on other sites More sharing options...
jacdx Posted December 26, 2011 Share Posted December 26, 2011 Resurrected!I just had this issue, but saved the backup/reload as the last resort. I didn't have to. Stopping/starting Director fixed it for me, refreshing navigators didn't.-J Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.