Costa Posted October 24, 2017 Share Posted October 24, 2017 Hello, I have some troubles with DENON AVR. Was manually add driver and entered right IP address. Device is Online in Network Connections. Just one function is available. When sending commands "Connect" and "Disconnect" from AVR properties in system design it switch network status from TRUE to FALSE (with Confirm N/W Connection message appears). Any other functions is not working. in Debug mode it prints next (when volume up is pressed on C4 remote) 17:54:50:129 ReceivedFromProxy: PULSE_VOL_UP from Binding: 5001 17:54:50:131 OUTPUT: 7000 17:54:50:134 ROOM_ID: 8 17:54:50:137 output: 0 17:54:50:139 bindingID: 5001 17:54:50:142 PULSE_VOL_UP-7000 17:54:50:145 changeVolume called! 17:54:50:148 Current Volume is 0Base Volume is 0 17:54:50:153 SetVolumeStep direction UP! 17:54:50:156 SetVolumeStep step is default! 17:54:50:158 Emit:MVUP 17:54:50:150 SetVolumeStep called! 17:54:50:220 SendToNetwork:MVUP 17:54:50:223 volRampTimerCount is : 0 17:54:51:370 Emit:PW? 17:54:51:477 SendToNetwork:PW? 17:54:51:479 volRampTimerCount is : 0 .... cyclically 17:56:26:541 Failed to receive poll responses... Disconnecting... 17:56:26:545 Network Connection Down. 17:56:26:602 bTrying, g_reconnect_timer = 5 sec 17:56:26:606 Network Connection Down. 17:56:31:538 gLastCheckin = 7 17:56:31:602 Attempting to reconnect to AVR... 17:56:31:606 bTrying, g_reconnect_timer = 5 sec 17:56:31:610 Network Connection Up. 17:56:31:612 OnConnStaChg gLastCheckin = 7 17:56:36:609 Attempting to reconnect to AVR... Any help will be appreciated Link to comment Share on other sites More sharing options...
Matt Posted October 24, 2017 Share Posted October 24, 2017 I am not following what you're attempting to do. Sending Connect will force the driver to attempt to connect to the receiver. This will set the driver to true since you've sent the connection message. Send Disconnect will force the driver to attempt to disconnect from the receiver. This will set the driver to false since you've sent the disconnected message. If on the latest version you could drag and drop the SDDP if the receiver is on the latest firmware, rather then manually typing in the IP address. Hopefully we can get some further information to help you narrow down the issue. Thanks, Matt Link to comment Share on other sites More sharing options...
Costa Posted October 24, 2017 Author Share Posted October 24, 2017 I thought it is status messages - true if link established and false if disconnected. In that case there are no link between C4 and Denon. C4 is 2.10.0 and DENON is on the latest firmware, but it is impossible to drag and drop because AVR is not in Discovered Items and when pressing and hold DIMMER and ZONE2 buttons, AVR shown "Control4 Identifying" message on LCD but nothing happens in Composer. Only manual adding is working. Link to comment Share on other sites More sharing options...
Matt Posted October 24, 2017 Share Posted October 24, 2017 What's the customer.control4.com account name and the IP address of the receiver? Matt Link to comment Share on other sites More sharing options...
Matt Posted October 24, 2017 Share Posted October 24, 2017 In the receiver setup, did you set the network control to 'always on' and HDMI control to 'off'? Matt Link to comment Share on other sites More sharing options...
Costa Posted October 25, 2017 Author Share Posted October 25, 2017 Yes, everything was set as described in manual. HDMI off - Network is always on. Local network is OK, even try another switch and router. Link to comment Share on other sites More sharing options...
Costa Posted October 25, 2017 Author Share Posted October 25, 2017 Amazing. Just after factory reset it`s working. Ctrl-alt-del still rules :))) Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.