Jump to content
C4 Forums | Control4

VINCELdUB

c4Forums Member
 View Profile  See their activity

  • Posts

    941

  • Joined

  • Last visited

  • Days Won

    12

 Content Type 

Posts posted by VINCELdUB

    C4-16amp3-b Partial Audio Sensing

    in General Control4 Discussion

    Posted

    I have a C4-16amp3-b that I never tried using audio sensing for programming. Now that I have tried I found that inputs 1-4 are sensing audio and inputs 5-8 are not. Is there a way to turn audio sensing on or are these 4 inputs just dead? 

    Most likely you have some dead inputs. I do not recall seeing any settings to adjust this.



    Sent from my iPhone using Tapatalk

    Need Help With C4-16S2-E-B

    in Troubleshooting, Workarounds, & Bugs

    Posted

    Do you have a voltmeter? Does anything light up on it when connected to power? I have successfully replaced the power supply in one of these before.

    Big caution!! Live electricity troubleshooting below. !!!

    You could open it up. Set volt meter to VAC and then test the leads going into the box. Then test the output of the power supply. 12vdc or 15vdc. If I recall.


    Sent from my iPhone using Tapatalk

    Just Add Power and Roon

    in Looking For An Integrator?

    Posted

    33 minutes ago, djheijs said:

    Bought components for Just-Add-Power and the 1st transmitter and 1st receiver are working properly sending through my Apple 4k signal (though very slow if on 4k, so I set it to 1080 for now).

    My stand-alone Roon setup seems to be working well, but would like to have it integration with the rest of the house.

    Our current dealer seems quite confused about what Just-Add-Power and Roon even is and seems generally to have more experience in different kind of setups (simpler) than mine.

    Anyone experienced in setting up Just-Add-Power and Roon remotely?

    J+P no problem. Roon, what is this? audio service?

     

    Remote Request - Need to Switch 2nd AppleTV from IP to IR

    in Looking For An Integrator?

    Posted

    1 minute ago, sooner2k1 said:

    I currently have 2 AppleTVs in my rack.  One was already switched to the IR driver by myself and my dealer remotely.  At the time I wasn't upgraded to iOS13 on the other and didn't have an extra IR cable to switch the second over.  

    I have an open IR port on the HC-800 controller and an extra cable and can handle the hands on piece, but need somebody to switch the AppleTV over from IP to IR for me.  I already have the IR driver in my system.    

    If it goes as smoothly as the first one with my local dealer, this should just take a few minutes.  I know most of you have a minimum rate, so if you can do this work can you message me and let me know what your minimum charge is?  I'm hoping to get this done this evening, or tomorrow evening.  

    Thanks

    Pm sent

    Digital Projection HIGHLite 4K 12000 Driver NEEDED

    in Driver Requests

    Posted

    3 minutes ago, VINCELdUB said:

    https://www.dropbox.com/s/2wgjpqbun1rokbi/projector_Digital Projection_HL 4K.c4i?dl=0

     

    or this one  

    https://www.dropbox.com/s/czeqor9eh14xbht/projector_Digital Projection_HL 4K(1).c4i?dl=0

    try this. One way. Basic commands as rs232

    Sorry for all of this. Have gone hunting through files and found this. It is working perfectly. 

     

    https://www.dropbox.com/s/mqut78k1xa8us2c/digital_projection_projector_annex4.c4z?dl=0

     

    annex4 built it. 

    Programming with Advanced Lighting Scenes

    in Programming with Composer

    Posted

    2 minutes ago, LollerAgent said:

    Sorry for resurrecting such an old thread.

    I have a keypad where I bind a scene to each button.  When I press and hold any of the buttons that are bound to a scene, based on your description, should I expect the lights in that scene to dim?  This isn't happening for me.  Instead, the lights that are attached to the load of this keypad (which are outside of this scene) come on, and then all other lights in the room come on to 100%.  I'm honestly not sure what is happening here.  It would be nice if I could somehow use the same button that activated the scene to dim the scene as well.

    Ok, first, “the other lights in the room come on” are they on the scene you want to dim?

     

    second, it sounds like the scene you are activating does not have a toggle scene created. To create one, go to agents. Then advanced lighting scenes. Then select the scene you are activating with the binding to a button. Then, along the top you will see a drop down menu for a toggle scene.

    clock the button that says, “ create toggle scene”.  

    Hope this helps. 

    Samsung Commercial Diplay

    in Driver Requests

    Posted

    9 minutes ago, VINCELdUB said:

    I am so sorry, I was not following this thread and missed this. I do have the driver and will post the link shortly.I am so sorry, I was not following this thread and missed this. I do have the driver and will post the link shortly.

    https://www.dropbox.com/s/k78ot7qvl9jg5ml/tv_COLWIN CONNECT_UD Series ID ALL(1).c4i?dl=1

     This is the free driver. And below is the driver from ANNEX4

    https://annex4.link/drivers/samsung-mdc

     

    Samsung Commercial Diplay

    in Driver Requests

    Posted

    On 3/12/2019 at 10:35 AM, jasonl said:

    Hi,

     

    I am looking for a 1 way driver for Samsung commercial display, I only need to control power on/off and all input. Does someone have this ? I contacted Annex and they said that they don't have any driver for commercial display.

     

    Thanks

    I am so sorry, I was not following this thread and missed this. I do have the driver and will post the link shortly.I am so sorry, I was not following this thread and missed this. I do have the driver and will post the link shortly.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept