Jump to content


c4Forums Member
  • Content Count

  • Joined

  • Last visited

About bigdaddyo811

  • Rank
    Control4 End User

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Ok. That's what I was trying to do is go to 2.5 then up but doesnt work Sent from my iPhone using Tapatalk
  2. I tried that and it gave the same error Sent from my iPhone using Tapatalk
  3. See below. Steps 1,2 3 and what I get. Thanks for your help
  4. I get the same error with v2 Sent from my iPhone using Tapatalk
  5. I am using the v1 updater and the error is ": "Failed to download the 2.5.3-res.xml file from the http://update.control4.com/release2 location". I was trying to get to 2.53 because that's the only option that populates on the v1 updater. I figured I would use the v1 to get to 2.53 and then use v2 to try to get to 2.9
  6. Oh yes 2.91. Thanks. Any ideas how to get this one to 2.9 Sent from my iPhone using Tapatalk
  7. Why? The other 5 and 7s in this system did Sent from my iPhone using Tapatalk
  8. I have a 5" touchscreen pulled out of storage. Trying to update from 2.1.1 to 2.10 I tried the C4_Device Image update v1 and v2 . V2 doesnt work" as not up to 2.5 When I run v1, to get to 2.5.3 I get the following error: "Failed to download the 2.5.3-res.xml file from the http://update.control4.com/release2 location" Any ideas?
  9. For those trying to get this work, these steps all work, but you must change the Garage Relay to a TOGGLE instead of a Pulse and then it works. Thanks
  10. I follwed these instructions, but when I hit OPEN door under the Garage door, it does not work. It does work fine to open and close within Vera so the problem is between C4 and the door 1. Identified Vera controller - status says connected 2. Added Garage Door Relay 3. Added zwave door lock. Added Room/Section/Device and ID updates in the ID section so connected to controller 4. Bound Zwave door lock to Vera and zwave relay to Garage Door 5. Hit OPEN door on Garage door relay (double click and hit OPEN door) and nothing happens. Any ideas? Thanks
  11. I purchased a H264 RTSP POE 1080p IP camera and am using the generic IP driver as well as a HIKVision driver. With the RSTP feed for the H264 as rtsp:// the camera shows up fine when I am on the network. The feed works fine on the android app when I am on the network. When I move to 4sight over cellular, the feed does not show up in the android app. All my other cameras (panasonic and wirepath cameras) show up fine. Anyone know why that would be the case? Thanks
  12. I am having problems with OPEN/CLOSE. If I say "CLOSE 'Bedroom Drapes' " - this works fine and drapes close If I say "OPEN 'Bedroom Drapes' " echo says - "im not sure how to help you with that". (the Turn ON 'Bedroom Drapes' works fine". I thought OPEN and ON were equivalents. Thanks
  13. The speaker wires for the first 2 speakers run to one rack. The speaker wires for the new set of 2 speakers runs to a different rack. I may not understand your question, but I cant hook them to the same output on the C4 amp. If you mean program the two sets of speakers into the same zone - that's what I want to do, but dont know how. We tried to put amp 1 to Audio endpoint 1 and amp 2 to audio endpoint 2 in the same room/zone but it didnt work. We dont understand endpoints... If we can somehow assign the output of the speakers on amp1 and output of speakers on amp 2 to the same zone, that would be what I want Thanks
  14. Could you elaborate in a way I could print and pass to dealer? Thanks
  • Create New...