sbenzie Posted April 20, 2012 Share Posted April 20, 2012 I noticed yesterday my HC800 has connected at 10M-Half Duplex ????I thought this is a bit slow, was expecting at least 100M-Full Duplex.Any ideas ?? Link to comment Share on other sites More sharing options...
thecodeman Posted April 20, 2012 Share Posted April 20, 2012 Well, the port is Gigabit on the HC800 so I would check to see what it's plugged into. Link to comment Share on other sites More sharing options...
sbenzie Posted April 28, 2012 Author Share Posted April 28, 2012 Its plugged into a NETGEAR FS726TP switch, which does 100M full duplex.See the attached for what is shown, I have highlighted the C4 port Link to comment Share on other sites More sharing options...
CFUG Posted April 28, 2012 Share Posted April 28, 2012 ehhh, 100mbps is not gigabyte speed. Your port g6 appears to be your controller and it is showing 10M/half duplex connection? Can you force the config to 1000M on that port? I have a 724 switch and it's showing 1000Mbps status at the moment. Link to comment Share on other sites More sharing options...
sbenzie Posted April 29, 2012 Author Share Posted April 29, 2012 Tried moving it onto a gigi port, but no change the hc800 is at half duplex. Also tried to for the signal from the switch side, nothing.Just tried a new cable but got the same issue, so not really sure what is the issue. All my other devices are full duplex 100M.....Guess I need to figure out how to contact C4 and see if there is a bug on the HC800..... Link to comment Share on other sites More sharing options...
msgreenf Posted April 29, 2012 Share Posted April 29, 2012 Are you using cat6? Link to comment Share on other sites More sharing options...
sbenzie Posted April 29, 2012 Author Share Posted April 29, 2012 The cable is a Cat 5E, standard Ethernet cable. Link to comment Share on other sites More sharing options...
msgreenf Posted April 29, 2012 Share Posted April 29, 2012 The cable is a Cat 5E, standard Ethernet cable.Gigabit requires cat6 Link to comment Share on other sites More sharing options...
chicagoskiguy Posted April 29, 2012 Share Posted April 29, 2012 Gigabit only requires cat5 or better.http://en.wikipedia.org/wiki/Gigabit_Ethernet Link to comment Share on other sites More sharing options...
sbenzie Posted April 29, 2012 Author Share Posted April 29, 2012 The cable is a Cat 5E' date=' standard Ethernet cable.[/quote']Gigabit requires cat6Which might or might not be true but I`m getting 10M half duplex, thats pretty poo !! Link to comment Share on other sites More sharing options...
hgrey Posted November 4, 2015 Share Posted November 4, 2015 Hi, I'm having the same issue, did you ever find a solution? I'm also using a netgear switch, although not the same model. thanks Link to comment Share on other sites More sharing options...
dgbrown Posted November 5, 2015 Share Posted November 5, 2015 Try turning off autonegociation on the switch port. Then set the switch port and Ethernet on the controller to gbe full duplex. Might be a handshaking problem. Link to comment Share on other sites More sharing options...
christophers Posted November 5, 2015 Share Posted November 5, 2015 spit-sw1#sh int gi0/26 status Port Name Status Vlan Duplex Speed TypeGi0/26 connected 1 a-full a-1000 10/100/1000BaseTXspit-sw1# although the controller sucks at dealing with STP and other things, it seems to be at 1000GbE see: spit-sw1#sh int gi0/26 controller GigabitEthernet0/26 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is 1ce8.5dbf.291a (bia 1ce8.5dbf.291a) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 2787 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 2000 bits/sec, 4 packets/sec 5 minute output rate 25000 bits/sec, 16 packets/sec 25438554 packets input, 4343090277 bytes, 0 no buffer Received 275074 broadcasts (114220 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 114220 multicast, 0 pause input 0 input packets with dribble condition detected 54019014 packets output, 13765760647 bytes, 0 underruns 0 output errors, 3159753 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out Transmit GigabitEthernet0/26 Receive 880860639 Bytes 48123468 Bytes 27113215 Unicast frames 25163487 Unicast frames 18772430 Multicast frames 114220 Multicast frames 8133390 Broadcast frames 160854 Broadcast frames 0 Too old frames 4276349267 Unicast bytes 108433 Deferred frames 23791834 Multicast bytes 0 MTU exceeded frames 15659178 Broadcast bytes 2034440 1 collision frames 0 Alignment errors 773529 2 collision frames 0 FCS errors 285591 3 collision frames 0 Oversize frames 56498 4 collision frames 0 Undersize frames 6212 5 collision frames 4722074 Collision fragments 1066 6 collision frames 662 7 collision frames 3578887 Minimum size frames 732 8 collision frames 17604049 65 to 127 byte frames 640 9 collision frames 1343515 128 to 255 byte frames 252 10 collision frames 838951 256 to 511 byte frames 70 11 collision frames 1002395 512 to 1023 byte frames 23 12 collision frames 1070764 1024 to 1518 byte frames 17 13 collision frames 0 Overrun frames 7 14 collision frames 0 Pause frames 4 15 collision frames 10 Excessive collisions 0 Symbol error frames 0 Late collisions 0 Invalid frames, too large 0 VLAN discard frames 0 Valid frames, too large 0 Excess defer frames 4722074 Invalid frames, too small 12173367 64 byte frames 0 Valid frames, too small 26210846 127 byte frames 6307830 255 byte frames 0 Too old frames 2745394 511 byte frames 0 Valid oversize frames 1279066 1023 byte frames 0 System FCS error frames 5302532 1518 byte frames 0 RxPortFifoFull drop frame 0 Too large frames 2034440 Good (1 coll) frames 1125303 Good (>1 coll) frames c4, if you're reading this, you need some good network engineers.... Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.