BREAL Posted February 27, 2015 Posted February 27, 2015 Hey everyone I'm trying to program a 6 button keypad switch. The second one down on the keypad that I'm trying to program is called "Movie" I've attached a photo. I want to press the button and then have it activate the "Media Movie" advanced lighting scene and turn on the Dvd Player while pressed. I attached a picture of the programming I've done so far. Everytime I press the button the lights turn on perfectly then the DVD player turns on same with the Tv and it looks perfect for about two seconds. Two seconds later the TV turns off, any clue why the TV is turning off?
Matt Lowe Posted February 27, 2015 Posted February 27, 2015 when the tv turns off does C4 in the zones page still show that the room is on? If yes something with the tv control. if no some other programming is turning the room off.
BREAL Posted February 27, 2015 Author Posted February 27, 2015 Yeah the zone is still on but the TV turns off. Those are the only changes I've done to my system. Now it's happening also when I hit watch Tivo or watch DVD with the remote control everything turns on except the TV, this is driving me nuts. Anyone know what could be wrong?
Matt Lowe Posted February 27, 2015 Posted February 27, 2015 model number of the tv? Driver your using to control? Control method? likely this is a ir driver and is using power toggle and the tv is in a incorrect power state.
BREAL Posted February 27, 2015 Author Posted February 27, 2015 Sony XBR-65HX929. Not sure what driver it's using how do i find that out? Everything was working fine until I programmed those two little scripts for that Media Movie button.
Matt Lowe Posted February 27, 2015 Posted February 27, 2015 driver shows it uses discrete power. doubt that is part of the issue. if you turn the room on using remote or the room. does it happen?
BREAL Posted February 27, 2015 Author Posted February 27, 2015 Yes now it started happening with the remote too, everything turns on except the TV.
Matt Lowe Posted February 27, 2015 Posted February 27, 2015 might be the tv. can you turn the tv on manually. if this is repeated likely the tv
BREAL Posted February 27, 2015 Author Posted February 27, 2015 it's not the TV because I can turn on the TV manually, and everything works fine. I've tried turning everything off in the room and the whole house and I keep getting the TV to not turn on with any command like watch Tivo or Watch DVD.
BREAL Posted February 27, 2015 Author Posted February 27, 2015 Hey everyone I'm trying to program a 6 button keypad switch. The second one down on the keypad that I'm trying to program is called "Movie" I've attached a photo. I want to press the button and then have it activate the "Media Movie" advanced lighting scene and turn on the Dvd Player while pressed. I attached a picture of the programming I've done so far. Everytime I press the button the lights turn on perfectly then the DVD player turns on same with the Tv and it looks perfect for about two seconds. Two seconds later the TV turns off, any clue why the TV is turning off? Anyone have a clue why all of a sudden now the TV won't turn on with any button I hit on the remote like watch TV or Watch DVD. The TV Just stays off it's so bizarre. Everything worked perfectly yesterday. Is it because of this tiny little programming I did, that's all I can think of. I attached a pic of the programming that I did.
msgreenf Posted February 27, 2015 Posted February 27, 2015 Do you have cec disabled on the TV? Sent from my XT1060 using Tapatalk
AK1 Posted February 27, 2015 Posted February 27, 2015 What is the TV connected to? An AV receiver? Is there a video matrix in the project? You'll also want to unplug the TV for a few seconds and plug it back in to make sure it's behaving correctly.
BREAL Posted February 27, 2015 Author Posted February 27, 2015 Not sure about cec being disabled where do I find that info? Yes the TV is connected to a Pioneer SC-77 AV receiver. Where do I look in composer to see if there is a video matrix in the project? I'm guessing there is a video matrix. I will try unplugging the TV.Sent from my iPhone using Tapatalk
cybuch Posted March 10, 2015 Posted March 10, 2015 Sounds like CEC Issue. Disable it in the settings of the TV and see if that helps
Rod Matthews Posted July 6, 2015 Posted July 6, 2015 Maybe in programing you can select the room and make a conditional of when a video source is selected> turn the tv on. Also make a custom button that turns the tv on only and that way you can confirm the driver is doing what it is supposed to
Recommended Posts
Archived
This topic is now archived and is closed to further replies.