Time2Jet Posted September 28, 2019 Posted September 28, 2019 All, Will these motion sensors work with OS3.1? Thanks!
Time2Jet Posted September 28, 2019 Author Posted September 28, 2019 Thanks Mitch. I can’t seem to get them to add. I’ve reset the mesh on them (powered on while holding the button for 10 seconds), but the 4 press routine doesn’t seem to populate them. I’ve tried the card access and C4 drivers. No luck. Tried many many times. My Zigbee mesh is working fine all other Zigbee devices look great. I’ve tried several different sensors. Sent from my iPhone using Tapatalk
Time2Jet Posted September 28, 2019 Author Posted September 28, 2019 Are they used? lol, yes. Probably old as dirt. They came from a working system though. A friend gave me 8 of them to play with programming events off of motion. Sent from my iPhone using Tapatalk
msgreenf Posted September 28, 2019 Posted September 28, 2019 They likely need to be reset w 13 taps before joining a new mesh
Time2Jet Posted September 28, 2019 Author Posted September 28, 2019 They likely need to be reset w 13 taps before joining a new mesh No good Mitch. But maybe you can look at it and a few other things when you have a minute. I’ll pm you. Thanks! Sent from my iPhone using Tapatalk
msgreenf Posted September 28, 2019 Posted September 28, 2019 When you tap the button 13x what does the led flash?
Time2Jet Posted September 28, 2019 Author Posted September 28, 2019 When you tap the button 13x what does the led flash? It continuously cycles red/green/amberSent from my iPhone using Tapatalk
Time2Jet Posted September 28, 2019 Author Posted September 28, 2019 Or maybe just red/green cycle pretty rapid. Sent from my iPhone using Tapatalk
msgreenf Posted September 28, 2019 Posted September 28, 2019 when you powered on and held it down for 10 seconds did the light turn amber? once it turns amber you should let go
Time2Jet Posted September 28, 2019 Author Posted September 28, 2019 when you powered on and held it down for 10 seconds did the light turn amber? once it turns amber you should let goUnfortunately, yes. I did all of that pretty carefully. I let go when it turned amber. When I do the 13 taps, it’s actually amber (as they call the alternating rapid blinks). It’s trying to join. I even walked it back to the rack hoping it would connect. No luck yet. Sent from my iPhone using Tapatalk
msgreenf Posted September 28, 2019 Posted September 28, 2019 And you are doing 4 taps after you have the id window open?
Time2Jet Posted September 28, 2019 Author Posted September 28, 2019 And you are doing 4 taps after you have the id window open? I am. When I read the Card Access literature, it mentions making sure auto discover is enabled. I don’t see that as an option, so I assume that’s referring to general Zigbee Pro and not specifically do C4. The devices are old as is the driver. I see both a CA and a C4 driver. I’m using the CA version which looks like it’s is a little older, but the id screens are identical. They both say wms10. Puzzling. I’d like to try to re-add a different Zigbee device to see if it identifies, but everything I have Zigbee is already connected and I don’t want to risk removing add re-adding. Sent from my iPhone using Tapatalk
msgreenf Posted September 28, 2019 Posted September 28, 2019 What driver are you using? I think there is only one
Time2Jet Posted September 28, 2019 Author Posted September 28, 2019 Card Access WMS10. I’ll check the version and date and post. I had to run to the office quick. There is a C4 driver that also says “WMS10” If I remember correctly, it was a little later date. Sent from my iPhone using Tapatalk
Cyknight Posted September 28, 2019 Posted September 28, 2019 If older, there's a chance they are on embernet, not pro.
Time2Jet Posted September 28, 2019 Author Posted September 28, 2019 Thanks @cyknight. That was my first thought, but the model number would indicate Pro WMS10-2-ZPSent from my iPhone using Tapatalk
msgreenf Posted September 29, 2019 Posted September 29, 2019 card access wireless motion is the correct driver. version 2, last modified 2/10/2009 cardaccess_wirelesspir.c4i
Time2Jet Posted September 29, 2019 Author Posted September 29, 2019 card access wireless motion is the correct driver. version 2, last modified 2/10/2009 cardaccess_wirelesspir.c4iThanks Mitch. That’s the one I was working with. I tried removing the driver and re-adding it several times while I worked through the steps you suggested. Sent from my iPhone using Tapatalk
PenguinOpus Posted October 2, 2019 Posted October 2, 2019 I'm having the same trouble. I have a WMS10-2-ZP. Running OS3.1. I've tried both the C4 (2015)and Cardaccess (2009) drivers. Power on holding button, wait 10 seconds, get solid red+green. Light goes out. Then start getting 2 green flashes, followed by long green, repeats forever. Open identify dialog in Composer 3.1, choose Mesh, hit button 4 times. No change in lights Hit button 13 times, get nearly simultaneous flashing red and green. Hit button 4 times, no change, still flashing red and green.
Time2Jet Posted October 2, 2019 Author Posted October 2, 2019 I’ve gotten no resolve yet. So I’ll be watching the thread too. Sent from my iPhone using Tapatalk
snipboy Posted October 7, 2019 Posted October 7, 2019 I had the exact same problem with the same steps about a year ago when I purchased a used one.
snipboy Posted October 7, 2019 Posted October 7, 2019 Mitch -- what did you do to get them added beyond the steps above? What is the magic you used?
Recommended Posts
Archived
This topic is now archived and is closed to further replies.