sdmat Posted July 27, 2019 Share Posted July 27, 2019 I have an HC800 on OS3. I have a Hikvision NVR 7608NI. The NVR was updated to some Hikvision firmware for C4 (obtained from Hikvision support). However, the NVR configuration doesn't have the "Security" tab. My dealer hasn't integrated Hikvision into C4 before. He wants me to be able to browse to each camera feed by IP to be able to integrate. My network is set up as 10.0.1.X and the NVR is on that network. It then creates a feed for each camera with IP 192.168.254.X. Not sure where to go from there. Any advice? Thanks, Scott Quote Link to comment Share on other sites More sharing options...
Cbell Posted July 27, 2019 Share Posted July 27, 2019 One thing you can look into is the Hikvision driver offered by Annex4. It looks like it offers direct camera control, as well as indirect via the NVR. Sent from my LM-V350 using Tapatalk Quote Link to comment Share on other sites More sharing options...
mallom Posted July 28, 2019 Share Posted July 28, 2019 What do you want to integrate exactly? 1) are you trying to control the NVR via control4 (NVR HDMI out going to the TV and control the menus of the NVR) 2) Or view the camera feeds on mobile phones/C4 GUI? For number 1 you need: a) C4 customer firmware (seems you already have it) b) add the NVR driver to the project c) Add the correct IP and credentials (I think it can be done via sddp as well) For number 2 you need a camera driver. I use the Generic Camera Driver. There is a post somewhere on this forum where you can get it from. (thats how I do it. Im sure there are better ways to accomplish this, but this works fine for me. The C4 Hikvision camera driver doesnt give me the correct URL stream for some reason) a) Download the Generic Camera Driver b) Assign the correct IP and Port for each camera. I have the same NVR and for me, this is how I get the streaming URL for each camera: NVR's IP: 111.222.333.444 If using POE: Camera1 would be: 111.222.333.444:65001 Camera2 would be: 111.222.333.444:65002 Camera3 would be: 111.222.333.444:65003 and etc.. Now you just have to assign the streaming URL. If you have Hikvision cameras, it should look something like this: RSTP: Streaming/Channels/X0Y - "X" corresponds the NVR channel - "Y" corresponds to the main or sub stream. So, if you want to grab the sub stream of channel number 1, the URL would look something like this: - Streaming/Channels/102 So, if you want to grab the main stream of channel number 5, the URL would look something like this: - Streaming/Channels/501 MJPEG: Streaming/channels/2/httppreview Snapshot: Streaming/channels/2/picture Good luck! c4toys 1 Quote Link to comment Share on other sites More sharing options...
Cyknight Posted July 28, 2019 Share Posted July 28, 2019 To see cams plugged into the hik nvr, you need to enable the virtual host setting - tell your dealer to look for the appropriate articles on how to do it in the C4 knowledge base (just search for hikvision). The above is largely correct off the top of my head by the way, but the kb aticles detail the steps. Quote Link to comment Share on other sites More sharing options...
mallom Posted July 28, 2019 Share Posted July 28, 2019 To see cams plugged into the hik nvr, you need to enable the virtual host setting - tell your dealer to look for the appropriate articles on how to do it in the C4 knowledge base (just search for hikvision). The above is largely correct off the top of my head by the way, but the kb aticles detail the steps.And to enable virtual host:Network > Advanced Settings > Other Quote Link to comment Share on other sites More sharing options...
sdmat Posted July 28, 2019 Author Share Posted July 28, 2019 Thank you all. I will see if this info helps my dealer. Scott Quote Link to comment Share on other sites More sharing options...
NickKayP Posted August 3, 2019 Share Posted August 3, 2019 Good morning, I am also intending to install 5 HIKvision IP PTZ cameras into a new build. Simple question. Can i control the camera pan, tilt and zoom via the control 4 app via the remote on the TV or do i still need the camera system keyboard. Appreciate any support and advice. Thanks, Nick P. Quote Link to comment Share on other sites More sharing options...
Gigatech Posted November 19, 2019 Share Posted November 19, 2019 On 7/28/2019 at 12:57 AM, Cyknight said: To see cams plugged into the hik nvr, you need to enable the virtual host setting - tell your dealer to look for the appropriate articles on how to do it in the C4 knowledge base (just search for hikvision). The above is largely correct off the top of my head by the way, but the kb aticles detail the steps. so with what are the paid drivers (driver central, annex4) any better Quote Link to comment Share on other sites More sharing options...
Cyknight Posted November 19, 2019 Share Posted November 19, 2019 41 minutes ago, Gigatech said: so with what are the paid drivers (driver central, annex4) any better Couldn't tell you, don't use them Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.