drmark12pa

Is there a difference between these two configurable dimmer keypads? Have multiple KC120277 but none of the KD120

One would hope they could get these dropouts on the streaming services fixed on the C4 end.

Ok doesn't sound like anything worth updating at this time then. I'm hoping for an update for streaming of Sirius as it often cuts out and it's not a network issue as streaming via web app is fine. Only through C4 interface is there an issue.

I was just told there is a new firmware update available... I cannot find any information what it contains or if it's worthwhile to update at this time.

I tried opening Composer this evening and am getting Runtime error (at 14:357) error? What the heck is this and how does one fix it? I tried uninstalling Composer and same error when trying to reinstall it. I'm running latest version of both firmware and the Composer.

When I came home for lunch the two buttons were lighting up as orange. I hit the button four times and it re-identified it now it's back in the project. It may be something to do with the temperature? I'm in Minnesota so it gets pretty cold at nights but during the day not as bad.

I have a basic C4 light switch in my gazebo which is a 3 season area detached from house so gets quite cold in winter. Recently the switch has gone offline for Control4. I have 2 other C4 switches and 1 C4 keypad (multibutton) in same location as well which are working fully. The disconnected switch works for physically pressing on/off but I cannot get it to reconnect. I've tried hitting top button 4 times. I've tried 9 times, I've tried 13 top, 9 bottom, 13 top to reset, I've tried resetting the breaker for that circuit... cannot get it back online. Any suggestions?

Having the same problem trying to connect remotely and I'm on the latest firmware

Has anyone experienced multiple thermostat disconnections today? I've attached a screenshot of my disconnections just this evening. I wasn't sure if perhaps control four was doing some maintenance of some sort that would have been pushing some kind of an update that would cause this.

4sight is up to date and I just upgraded to latest firmware on controller. I'll try a reboot which I did at least 5 times when firmware update was done to get security bus back online.

That's what I did but now when I try to reenable the C4 skill that is the message I'm getting.

For the past day after unlinking Alexa and Control4 in an attempt to correct what appeared to be lack of command response, I cannot link Alexa and Control4. Everytime I try I get Unable to link Control4 with Alexa. Is there an outage currently on either side of things?

It was correct email as they responded but basically said check with your dealer.

Today I suddenly noticed that Control4 is not working with my Alexa account. I have the Epic driver but also use some of the native C4 driver commands as well. Neither appears to be working. I tried unlinking my account in Alexa but now it won't let me add it back as it says it is having some trouble linking the account. Has anyone else had issues with Alexa as well as the Epic driver lately?

I've tested my emails and they work as far as successfully sending. I both my Verizon phone and other email I hadn't received alerts. I just upgraded firmware on the Luma 510 NVR last night a few alerts have come through but hit and miss. Nothing in spam.

My 2 cents on my Luma system as of late.... For the second time in 4 months my system is suddenly not sending ANY email/text alerts. I haven't changed anything and can successfully send test emails/texts but no actual triggered alerts come through. It's recording events but nothing is working. I sent an email to customers@control4.com as that's the only point of contact I could find. Not very good or easy technical support considering the cost of the 710 cameras I'm using.

Just started having issues with the Luma notifications AGAIN! I can successfully send test email alerts to both my Verizon phone and to my other email account but triggering events are currently not sending any notifications. Does anyone have any insight here as to why this seems to periodically happen with my Luma camera system (I have the 510 NVR and multiple 710 cameras).

The driver is $200?!?! Ouch.....

So is there any way of adding shuffle via remote after a playlist has been selected to play?

Hahaha I've noticed that if you play the playlist from the remote you can select it to play as SHUFFLE. However, I have it programmed so I can tell Alexa, "Alexa, Turn on playlist Cheap Trick" then there is no command on the remote to add shuffle even though I have it programmed to turn on playlist Cheap Trick and Shuffle On for the room but the shuffle isn't working for some reason. Strange... Also, I am old school and do like album start to finish but when you have an artist that has 20+ albums, it's nice to not listen to the same order every time!

I've just noticed since recent updates there is no way to turn shuffle on via remote. I've gone through every function under LISTEN on remote and that ability to.change okay behavior no longer exists!

I think the problem may have been the artwork was 2100x2000 or something in that range.... I know some players have difficulty processing if the embedded artwork is too high or at least in this case that seems to have resolved the issue by changing the artwork to a picture with lower resolution.... Just as an FYI possibly for future issues if anyone runs into this issue.

Also, with the quality factor when selecting a low number it seems a bit more muddy or full vs. a high number seems to tighten things up but I do lose a bit more bass when selecting the higher number it seems.

I want to improve the overall sound without the in wall speakers in the rooms clipping which is a fine line between maximizing the best response from in wall speakers and has been a bit tricky with the change from MP3 to FLAC there is definitely a difference for the better. This has necessitated readjusting each room's EQ and is a bit complicated because if you tweak one band it can change dramatically. I listen primarily to hard rock so it's hard to get the mid range so it doesn't sound like you're in a tin can while maximizing the lower end and not having ear splitting highs.

Is there a better way to fine tune the C4 amplifier sound settings without just experimenting with each of the frequency bands? There used to be the EQ app on the C4 homescreen but that has disappeared. Now I have to go into Composer and try to fine tune each zone which is not easy considering there about 30 bands in the EQ in advanced settings. Add to that the Quality Factor setting which I don't fully understand. I recently went back and updated my media library for my CDs to be all FLAC without compression vs. the previous MP3 at 360 so the quality much better. This has necessitated readjusting my EQ but wow what a task. I miss the EQ app in Composer but can't seem to find it anywhere anymore. Can anyone advise on how the Quality Factor setting affects play? Also, in the advanced settings for EQ it appears that you can select 5 bands to fine tune and I assume C4 just develops an EQ line based on these bands you've selected for Gain and Quality Factor.