-
Posts
682 -
Joined
-
Last visited
-
Days Won
11
Content Type
Profiles
Forums
Blogs
Gallery
Downloads
Events
Posts posted by mallom
-
-
You can't find the driver? Have an issue with the driver?
Have you tried a similar model? VSX-933 or VSX-932
-
-
Just now, atsokolas79 said:
I did you told me it was broken. I wanted a second opinion
Sent from my iPhone using TapatalkSo he didn't even try to contact Control4 just to check if it can be fixed or replaced?
-
Call your dealer. He *may* be able to get it fixed or replaced.
-
-
-
Call tech support (or ask your dealer to call) so they can change the resolution via putty.
If that doesn’t solve, it will be RMA. -
-
PS for the 8 zone (I think it also works on Audio matrices as well):
https://www.ebay.com/itm/AUDIO-PSU-ALP0800-Audio-Line-Switch-Mode-Power-Supply-960W-Continuous-/111004308644?hash=item19d85f54a4:g:DCUAAOSwcBhWXNVc
I have no clue what is the part number for the 4 zone. Can't find any info about it... -
So, after the increase to 75 devices AND the addition of fan switches (finally)... I need to add a bunch of switches. However, before I do, I want to make sure I understand the order of events and what I can / can't do in CHE? I can get all the switches, set them all up in Lutron app, but then I will need a dealer to add them into each room in C4 if i want to use them in CF scenes (like turn all off)? Is that correct?
Thanks guys,
-Matt
Correct!
Lutron hasnt created a driver for the Caseta Fan switches yet, BUT the RA Select Fan driver works flawlessly with Caseta. I personally have about 2 or 3 at home. -
Register your controller again. If you have 4sight, it should connect correctly.
-
-
My last post got tide to the wrong response.
I would like to investigate the experience button. It sounds easier
Sent from my LM-V350 using Tapatalk
Mine are set to run for 15 min (or 20min - cant remember) when they are manually switched on. Works perfectly fine for my needs. -
Looking to the best way to automate bathroom fans. I did some programming when they turned the light on the fan turns on and then when the light went off I delayed the 5 minutes and then the fan shuts off. What if they don't turn off the light at all but just walk out? Whats the best way to do this delayed shut off so they don't have fans running all the time?
Look for Extraction Fan experience button. It also works as a timer. -
To see cams plugged into the hik nvr, you need to enable the virtual host setting - tell your dealer to look for the appropriate articles on how to do it in the C4 knowledge base (just search for hikvision).
The above is largely correct off the top of my head by the way, but the kb aticles detail the steps.
And to enable virtual host:
Network > Advanced Settings > Other -
What do you want to integrate exactly?
1) are you trying to control the NVR via control4 (NVR HDMI out going to the TV and control the menus of the NVR)
2) Or view the camera feeds on mobile phones/C4 GUI?
For number 1 you need:
a) C4 customer firmware (seems you already have it)
b) add the NVR driver to the project
c) Add the correct IP and credentials (I think it can be done via sddp as well)For number 2 you need a camera driver. I use the Generic Camera Driver. There is a post somewhere on this forum where you can get it from. (thats how I do it. Im sure there are better ways to accomplish this, but this works fine for me. The C4 Hikvision camera driver doesnt give me the correct URL stream for some reason)
a) Download the Generic Camera Driver
b) Assign the correct IP and Port for each camera. I have the same NVR and for me, this is how I get the streaming URL for each camera:NVR's IP: 111.222.333.444
If using POE:
Camera1 would be: 111.222.333.444:65001
Camera2 would be: 111.222.333.444:65002
Camera3 would be: 111.222.333.444:65003
and etc..Now you just have to assign the streaming URL. If you have Hikvision cameras, it should look something like this:
RSTP: Streaming/Channels/X0Y
- "X" corresponds the NVR channel
- "Y" corresponds to the main or sub stream.So, if you want to grab the sub stream of channel number 1, the URL would look something like this:
- Streaming/Channels/102
So, if you want to grab the main stream of channel number 5, the URL would look something like this:
- Streaming/Channels/501
MJPEG: Streaming/channels/2/httppreview
Snapshot: Streaming/channels/2/picture
Good luck!
-
7 minutes ago, Control4@8293 said:
Just upgraded to 3.0 and my Lutron shaded are not functioning properly...dealer tried new drivers...cant figure ti out...anyone have the skill set for remote programming on this...happy to pay!
Define "not working properly".
What exactly is not working? -
-
Excuse my ghetto RA2 stickers. I need to get those buttons engraved asap. Lol -
-
Right - it is all on Apple - but hey, come here and blame control4 half cocked and then you are on a beta OS - so clearly control4 should work on betas without issues....Look in the mirror...
There is actually an official statement about why it doesnt work on HC controllers but I cant find it. If I do, I will update the thread. -
It is the architect that apple requires to integrate.
Sent from my Pixel 3 using Tapatalk
This!
Something something about security something that cant be implemented on HC controllers. -
Im not sure if you mean to quote my last post, but its the complete opposite of what I said.
You can create all your scenes within C4 if you want to. Thats how I do it.
I think some people prefer to create on Lutron’s side to minimize the popcorn effect and maybe reduce the CPU load on C4 controller, since all the processing would be done on Lutron’s side.
I have approx 70 dimmers/switches/fan total, 2 bridges and only use C4 Advanced lighting for scenes and ramp control. You cant configure ramping on Lutron’s side (AFAIK). -
Oh man... Just noticed that this is an old thread and everything has already been explained before. Hahah. Sorry!
Vsx 930 pionner driver?
in Driver Requests
Posted
Try this one VSX-LX303