ERDrPC

It seems like it should be simple, in the T3 shot, C4 recognizes "Front door open". Where is this stored so I can send it in a push notification??

I'm trying to send myself the name of the zone that causes the alarm to fail arming in a push notification. I would assume that would be "Trouble text" would have it I just opened my front door and tried to arm stay so I could see what values get written into the variables. "Last Arm failed" has the string value BYPASS. It always has this and I don't know why as I never bypass my alarm. "Trouble Text" is always blank "Trouble type" is always blank Partition state is always "disarmed ready" even when I have a zone open that would prevent arming. If I open a zone that would prevent the alarm panel itself from arming, it shows the correct error that it's unable to arm then by pressing the button on the panel it will tell me which zone. HOWEVER, C4 alarm screen on the T3 will always show the green ready to arm even if there is a zone open. Once I try to arm then the T3 shows unable to arm with the open zone. I just went through all of the system variables and I cannot find any variable that captures this info. Could my alarm be setup incorrectly? We have flood sensors in all of the bathrooms which are tied into the alarm but they don't count when arming or disarming the alarm...my installer did this. Could this be why Last arm failed always reports BYPASS as I figure the flood sensors have to be bypassed so they don't count??

@msgreenfSo I've opened the agent and here is the screen capture I'm stuck at what to do next

So all of the alarm zones are bound into C4. I've created a push notification for alarm fail using ${Security->Security::TROUBLE_TYPE} - reports blank everytime ${Security->House Security::LAST_ARM_FAILED} - reports "BYPASS" everytime ${Security->House Security::TROUBLE_TEXT} - reports blank everytime ${Security->House Security::OPEN_ZONE_COUNT} - this works ${Security->House Security::DISPLAY_TEXT} - reports "System ready type code to arm" however this isn't correct as the alarm display panel shows "System not ready to arm, press arrow" and when I press the arrow on the alarm panel is shows "25 Fault FRONT DOOR". When I open the front door and then open the alarm interface on my T3, C4 recognizes the front door is open. See attached screen shot. This can't be as hard as it seems???

I remember seeing a thread which provided the direct launch codes for android TV apps. I'm trying to find the one for Nest for a 2018 Sony. Anyone have it or know where to find it. Google search was not helpful.

Can you show us a pic. Want to get my integrator to do something like this.

Has anyone thought of a way to combine Waze and C4? I have 5 different sites where I work. I'd love to walk into the master bath and have Waze tell me the expected travel time or better yet time to leave to get there for x time. Does Waze have an API that C4 driver creators can use? Maybe use the T3 TS and the driver that shows webpages. Combine it with the new Google calendar driver so the system knows which of the 5 sites to show me. The trigger will be the tricky part....Emergency physicians are shift workers and there is a possibility of 11 different start times. As well my wife works at different jobs and I wouldn't want her walking into the bathroom or pressing the lights on scene and trigger my Waze. Heck....why not set it up for her schedule as well. Just want the system to more like Jarvis

I'm interested in this but I'm not sure which variable states I should care about. Any examples?

can the wyze cam's be set to record to a hikvision NvR?

Thanks - I will test this weekend

Is there a specific freq audio file that you use for the dogs

Do these new favorites replace experience buttons. Ie moving the door lock to the front page as a favorite. It can show lock and unlock status now as well as toggling it for usage.

So to answer your question - all of the zones are named and numbered in the alarm panel. They seem to be in C4 as well when you look at the properties and zones picture above. However, they are not listed under programming in the security alarm. All that is listed is Home security with its variables below, partition 2 to 8 below it. The water flood sensors have their own sensors so I guess that's what you mean with respect to binding into C4

I've spoken to my dealer and he is not sure where to get the info from. I'm hoping you superstars will have an idea. Does each zone have to have an alarm drive bound to it. I have lot of zones and my dealer didn't set it up that way

Anything about upgrading the resolution of the cameras on the 4 screen and 4k gui?

Bump... anyone have any idea where I can get the info for which zone caused the alarm not to arm?

I'm trying to setup push notifications where I can send the name of the zone that was in trouble or not ready state when trying to arm the alarm. I have a GE panel and the control4 driver for the Interlogix NetworX security system. I cannot find a variable where the zone number or name is stored. I'm hoping the Zone Name will be in a string variable that I can include in my push announcement. Eventually I'd like to create an audio announcement as well. I just need to figure out where to get the info about the zone causing the arm to fail

Working again android

Steamist does. Steam and normal shower control. There is a driver. Not IFTTT.

Not sure what changed but notifications are working again

Anyone else with the same issue?

I just realized that push notifications have stopped working a few days ago. My dealer came by today and upgraded to the latest OS. My android has C4 app notification as priority so they are supposed to always go thru. My 4sight license is active. Nothing else has changed. These are the notifications programmed in HE and not Alan's suite. I have rebooted my phone...No change. Dealer rebooted controller...no change Any ideas?

@alanchow I'm thinking of changing all of my outdoor soffit pot lights to LB230. However I cannot find anywhere if these can be used outdoors. I have a panelized lighting system with scenes and such setup for my current outdoor pots. Where I would like to implement the colour changing or strobe effect would be on alarm trigger, fire detector, christmas, party mode. I would like to do all of this with programming and not adjusting things on the fly at a touchscreen or using an app. Is this possible with the driver? I actually don't want my family to have access to the touch screen example you have above...I want my current screens to stay the same for simplicity. Is it possible to hide?

Lack of Atmos with first release of most movies in K store. Not quite K's fault as some studios don't allow UHD and full atmos in the K store. Have to wait and pay to upgrade for Atmos...ie pay for the same movie twice (although depending on the studio the amount second purchase amount varies)

So this doesn't need the Sam? I just bought that damn thing. What is a better solution ? Using Sam vs the driver? Which one will work if the internet is down?