dcovach

Thanks. I got your PM and looks like C4 already added the Spectrum TV mini app to the driver database a little while ago.

Log into your control4 account and read the bulletin at the top. PM me if you need a system update

The older module you have will physically fit in the newer locks but it doesn't work with it. You won't be able to get it to id into your project. The good news is that the newer module is much cheaper than the older one

You'll need to buy the newer module if you want the YR226. Or you can buy it from a c4 dealer with both lock and module included. Its not the same module as what you have.

HTI Customs created the driver above and they sell it on the Blackwire site. The free C4 roku driver only controls a Roku. No TV Commands

I contacted videostorm and they said (paraphrasing) that they may try to create a tool that generates the app id. I was lucky to get the right app id for a side loaded amazon prime video app (to work in canada on an American purchased fire tv) in a relatively short amount of time. I was unsuccessful in trying to find other app id's that work when trying to launch with a custom mini app driver. In hindsight... this should probably be in another thread

The Vera controller shows the ability to send yourself a notification when any or a specific pin code is entered. To send that status to C4, a scene could be created in the Vera Controller to turn on a Virtual Switch (then off after 5 seconds or so) when a specific or any pin code is entered and pair it with a Micasa relay driver in C4. A notification can be programmed in C4 when that switch turns on. Note... I have not tried this yet but all these options are showing as available in the Vera Controller.

Sent pm

I'm pretty sure the locale in your project needs to be set to a US city in order for the pandora driver to work even if you have a VPN

The ultimate solution for end user ocd mis-spelling or spelling preference is the renamer driver.

That drawing is good info. Helps with planning or understanding where/how devices (zigbee and wifi ap's) are/should be spread out to avoid connectivity or mesh issues.

That looks right. I usually like to add floors (basement, 2nd level) to show a basic visual layout. Sometimes it helps in understanding how far away one room might be from another if they're separated by one or two floors. Not always necessary. A drawing or quick phone call can sort that out too. Your house is probably a bungalow?

When you log in, do you see a message about the security patch? Is there a link somewhere there that gives you a choice of which version? I can also send you a link

One of the 3rd party drivers that was created by @msgreenf is also an Amcrest driver. It supports both brands. There isn't much of a way around not using the driver. It may be possible to add a free generic camera test driver for each of your cameras but that may require a little more work but you will not benefit from any of the enhanced motion sensing programming features of the 3rd party driver option. Your choice. Personally, I recommend the 3rd party option.

Make sure you download the updated newer version of composer he 2.10 (patched) from the link shown when you log into your control4.com account. There will be a message about this. It should get you connected to your project again.

As long as your controller OS is on at least 2.91, you should be able to take advantage of any of the available 3rd party dahua drivers. As for reputable dealers, you'll know you picked the right one when you feel like you got value for the buck. A fair dealer will throw in a couple freebies or fix a couple obvious flaws while they're in your system. You're not expected to know how much more you can squeeze out of your system without extra cost so I try to throw the options out there or just add the features right there and then at no extra cost. I'll even do a few programming examples to help steer them on the right track. Not all of us advertise as we're not looking to spread ourselves thin. I frequent the forums on my free time and try to be available at the very present moment when I notice someone who's having issues or needs integration. I could vouch for the persons mentioned above as well.

I do remote programming for my clients upon request. I also service those who do not have a local dealer that's available. I'll send you a pm.

There must be a newer Kb article that I haven't seen yet. Nice job

I should have been more specific. I wired the output wires of the 930 straight into one of the ea5 contact sensors. It works. I've never used an elk924 yet but it looks useful for some applications. I'm not sure if you need it for your setup

Good stuff. I used ran the 2 wires out of the 930 into the closest contact sensor (12v and sig). The C4 contact sensor does close on a doorbell press so I can program any action.

Very cool. Why do you need the ELK924? Are the wires going into the ELK930 from the doorbell transformer?

@SMHarman Spectrum TV channel is 23048

Thanks. I'll PM you when I get to that. Appreciate it. I may try to tackle making these drivers on my own once I'm able to see what you did.

Good question. How would I find that?

Would you be able to make the mini app driver for Spectrum TV? Would really appreciate it!