sonic30101

I use lutron radio ra2 geofencing to trigger macros as well as their widgets on android.

No good way that I am aware of for this. Ideally when a receiver is used sonos should be set to fixed. What is the reasoning to want the sonos volume to be variable?

If you are you using cable boxes/appletv/rokus there are some workarounds you can do to have left source s and right sources with volume endpoints being the 2 tvs. But if you are using built in services of the tvs control4 doesn't have a clean way that I have come across to understand 2 tvs in 1 room.

Are there any other zigbee devices like light switches or thermostats as part of your system. Are they working, and how large is the control4 system? I am wondering if you have a smaller controller on that side of the house that is on a different ip address with the different network and your zigbee is off on that side of the house.

Control4 LU1E receivers? Are you using the IR ports on them?

I don't think LAN or IR passthrough will work

How many audio outputs from the way are connected to your audio matrix/matrix amp

App or remote control? Make sure you are in the right room. Otherwise there may be a binding that is disconnected which a dealer will need to resolve.

You need to add more rokus to your distributed video system so they don't interfere with simultaneous sessions since there is only 1 roku currently to share

Are there dedicated rokus for each room or is there a hdmi switch in a centralized location sharing a few video sources throughout the whole house.

I prefer jesse smiths appletv ir driver since IP has had its ups and downs over the years and generations

C4 uses zigbee pro so you have to use a c4 controllers mesh to set up the device. Once it is programmed in c4 you can link to alexa but not native.

Roku doesn't have numbers as an available input command unfortunately

The matrix amp only has speaker outputs not rca to feed the dumb amp. So you should have an audio matrix probably the triad ams24. That allows you to exceed 9 zones for the 8 zones on your matrix amp plus the new amp.

If you have a c4 matrix amp that is maxed out and you want to add a single zone you may have some issues depending on what you want this additional zone to be able to listen to. What are your sources that are connected to the existing rooms? That amp you linked is a dumb amp so it needs signal fed into it. So if all you want is c4 music you need to plug an open output of a c4 processor into it and connect your speakers. If you have cable boxes and other sources you won't be able to listen to them in that zone without adding an audio matrix and locking the matrix amps inputs or some other hoop jumping to accomplish source selection

I don't believe there is a huge motion sensor or any of their keypad drivers. Only lights from what I have seen.

A possible strange double nat situation? Do you have a modem and separate router or access points? And if your phone is on the wrong one you may not be able to connect assuming the 4sight item to check below. Also do you have an active 4signt license on customer.control4.com

Any power lights on the amps? What amps do you have? Have you changed your network config recently? Do you have control of tvs if integrated? Does the control4 app work and connect? Are you using control4 music or a streamer like sonos?

How old is the processor? If it is a hc250 or hc800 before the model number had a -1 at the end. Handing over the account with the house would be beneficial to the new owner since the licenses are tied to the account. If not it really doesn't matter much for security once email and password are updated. Are you using Google home or Alexa? That would also be tied to your account too so be aware of that.

Try using the cd input for your controllers audio or sonos. That should allow for the last video source to pass through while listening to music.

Leon and sonance as well in the list of options

Needs to have good wifi and reasonable proximity to the directly controlled devices

Cut the ends off at the extender and land them into this in the right pinout https://www.amazon.com/dp/B07PMRCMCT/ref=cm_sw_r_cp_apa_glt_fabc_XD84WKYQ5RA1YPFF9PN9

Will be hard to find one, I think they had power supply and edid problems. Avpro edge for that size or going local with rokus and audio return for distributed audio are our solutions with best results.

Do you have a sensor on the garage door as well or just the relay to toggle the button press? Without feedback status the open command could be unreliable.