Dueport

Thanks again to @RAV - I now understand how lighting scenes in Zigbee work (which I did not previously).
Unfortunately, this did not fix my problem.  
After a lot of tinkering, I have been able to figure out what is causing my issue and, essentially, OS3.4.2 has created an issue in my system linked to my security driver (or the security proxy).
In summary, if I have a programming command that controls lights or an advanced lighting scene that runs within a short time of my security system being armed or disarmed then the command fails more often than it works (more accurately, if I have 2 or 3 lighting commands, the second and third ones fail).  As soon as I add a 30 second delay after the arm / disarm command before the lighting commands, everything is good again.  Sadly, this worked perfectly up until this OS release (with no delay needed).
 
 

We pride ourselves in being the largest and best driver developer.  As such support is important to us. Chowmain provides 19 hours of technical support via phone, chat and ticket a day (mon - fri) manned by a team of 6.
We want to ensure our customers are happy with the driver before they commit so we provide a 90 day trial.  This 90 days is plenty to get a understanding of if the driver is right to you.
I know you have a solution now so this driver probably isn't for you however you should reach out to the MyQ driver developer in regards to your grievances.  I am not sure if they can provide you with a refund or not but might be worth a shot.

Bumping this topic as Tidal now provides the higher quality audio on its standard tier.  
 
Firstly, I am keen to understand how to access this on Control4.  The driver properties say that I need to log in with a Hifi account to change the settings but all accounts are now Hifi and the driver does not seem to recognise this?
Secondly, after the upgrade certain songs on my playlists started stuttering in playback.  It seems like these are the higher quality tracks.  The only way I could fix this was limiting the quality in the Tidal driver (which defeats the purspose.

Yes, the fan controller buttons are fully programmable - unlike the KC120277 the layout just can't be changed.
For the record:
KC = configurable keypad. Doesn't control a load itself
KD = is a keypad and dimmer in one, so controls a load as a dimmer (and yes not what you want here at all)
KA = something else entirely in that it's a special device to act as a multi-way switch for cheap (think top and bottom of stairs), no programming involved (or possible) and looks like a C4 regular switch or dimmer but no leds.

"Mitch fixed it"?  haha, well i didn't fix it, I just clicked upgrade!  Happy to help anyone else upgrade to 3.4.2

@msgreenf fixed it for me with bindings - thank you!
As an aside: I recently purchased Text Expander and I think I'm going to add the phrase "Mitch fixed it" to Text Expander given how often that happens 😎

I would not recommend using anything other than Control4 keypads, or a Control4 touchscreen.  The Control4 keypads are modern looking if you go with the Contemporary button style...I install them in many client homes that are worth 10+ Million and they are perfectly happy with them.

Hello!
I've just released v20 of this driver, it adds support for OS 3.4.2 and also adds a property to increase/decrease the volume of Google Speech announcements
There's also a sale on the driver price for the next couple of weeks

Fixed

Apr 10, 12:18 EDT
Investigating - We have identified an issue with customer.control4.com, mydot.control4.com, composer pro and controller registration.. We are aware of and actively investigating solutions and impact. More details to follow. Thanks, Your Snap One Engineering team
View the full article

Probably not you.
Post in the dealer forum about slow loading this morning, reproduced by and service ticket thus created by a Control4 employee.

Put a Shelly relay inside the box and use the outlet vendor of your choice.

I stand corrected. I did not realize Kasa made in-wall outlets! I just looked it up and found the KP200. I had never seen that before. 
As I was wrong about any in-wall outlet by them, there may very well be a UK version. 

That's too bad that they don't make a UK version of their US in-wall outlet - we have several and they work very well. Hopefully a version of it gets to the UK soon.

Prompt, reliable, trustworthy, high-value are just a few ways to describe Mitch's service. 

Cleary they did something but it was silent I didn't do anything but try again and it worked 

We've just launched a fix at DriverCentral. v20240405 updates the graphics to something more iOS friendly.
We have tested this on an iPad both Portrait and Horizontal landscape. Please let us know if this has not resolved your issue.
Also, please ensure you Refresh Navigators after the update has been applied.

I can confirm the one unit i personally had impacted is resolved as of this morning!

Latest word from Roku directly to large partners is that they expect to have it fixed by the end of the week.

Thanks for reporting back on the iOS issue everyone.
Looks like it's an oversight on iOS webview supported graphic formats.
We will have an update released in the next few hours and report back. Apologies.

Overview
This driver interfaces with the SolarEdge API to collect and store values for Solar Power generated, Power consumed by the Site, and Grid Power used by or returned to the Grid.
All values are updated every 6 minutes due API limits imposed by SolarEdge.
Features
Clean UI Displays Grid Power, Consumption and Solar Power Displays Daily Totals Programmable variables for: Grid Power Consumption Solar Power Connection Status Exporting/Importing Daily Totals *Note: Consumption and Grid Power is only supported on SolarEdge systems configured with appropriate energy meters.
Limitations
Due to API limitations, data refresh is only updated every 6 minutes. 
Daily Totals are updated at 30 minute intervals. Consumption and Grid Power is only supported on SolarEdge systems configured with energy meters. For systems that only support displaying Solar Power, power readings will only update every 15 minutes. Only tested on single Inverter systems Trial
This driver comes with a 30 day trial, which begins the moment a dealer installs the driver. This should allow sufficient time to test functionality and ensure this driver meets your requirements.
FAQ
Why does the UI say 'Offline' and won't update?
Ensure you check:
Your inverter is still connected to the internet There is no outage on for the SolarEdge API Your Controller has the correct date/time for your time zone. Note: Connection issues can be typically confirmed by opening the mySolarEdge App on your phone, and checking the app still has a connection to your inverter.
Does this driver support batteries?
Not at this time. If you are interested, reach out.
 
Available at DriverCentral:
https://drivercentral.io/platforms/control4-drivers/utility/solaredge/
 
                                           
 

Roku has confirmed this will be fixed by end of week 

Control4 is aware of the problem, it started Friday and as far as they can tell it's a Roku problem...

Apr 1, 15:27 EDT
Identified - Numerous cases have been reported in the last few days of the loss of control of Roku devices through the Control4 system. There have not been any changes to the Roku driver recently and we currently leverage the published APIs by Roku, so we believe this is tied to a recent software update deployed by Roku. A Roku developer forum thread is also pointing to the same issue View the full article

The iOS team hasn't been able to get to testing of Apple Vision Pro yet due to higher priorities, but once they are able to give it a once over I would be happy to give you early access and get your feedback.